52132A 1 Mariner BEARING CARRIER ASSEMBLY (MERC 850 LONG)


52132A 1 BEARING CARRIER ASSEMBLY (MERC 850 LONG) Mariner 7085507 BEARING
52132A 1 BEARING CARRIER ASSEMBLY (MERC 850 LONG) Mariner
Rating:
28

Buy BEARING CARRIER ASSEMBLY (MERC 850 LONG) 52132A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 68
 

Compatible models:

7085507   Mariner

Information:

The engine is equipped with an Electronic Control Module (ECM). The ECM contains no moving parts. Follow the troubleshooting procedures in this manual in order to be sure that replacing the ECM will correct the fault. Verify that the suspect ECM is the cause of the fault.Note: Ensure that the ECM is receiving power and that the ECM is properly grounded before replacement of the ECM is attempted. Refer to the schematic diagram.Using a Test ECM
A test ECM can be used in order to determine if the ECM on the engine is faulty. Install a test ECM in place of the suspect ECM. Install the flash file into the test ECM. Program the parameters for the test ECM. The parameters must match the parameters in the suspect ECM. Refer to the following test steps for details. If the test ECM resolves the fault, reconnect the suspect ECM. Verify that the fault returns. If the fault returns, replace the ECM.Use the electronic service tool to read the parameters in the suspect ECM. Record the parameters in the suspect ECM. Install the flash file into the new ECM. After the ECM is installed on the engine, the parameters must be programmed into the new ECM.Note: When a new ECM is not available, you may need to remove an ECM from an engine that is not in service. The ECM must have the same serial number suffix. Ensure that the replacement ECM and the flash file match the suspect ECM. Be sure to record the parameters from the replacement ECM. Use the "Copy Configuration ECM Replacement" function in the electronic service tool.
If the flash file and engine application are not matched, engine damage may result.
Replacement of the ECM
Perform the following procedure in order to replace the ECM.
Connect the electronic service tool to the diagnostic connector.
Use the "Copy Configuration ECM Replacement" function on the electronic service tool. If the "Copy Configuration" is successful, proceed to Step 5. If the "Copy Configuration" failed, proceed to Step 3. Note: Record any logged faults and events.
Record the following parameters:
Record all of the parameters on the "Configuration" screen.
Record all of the parameters on the "Throttle Configuration" screen.
Record all of the parameters on the "Mode Configuration" screen.Note: If the parameters cannot be read, the parameters must be obtained elsewhere. Some parameters are stamped on the engine information plate, but most parameters must be obtained from the TMI data on the Caterpillar Secured Internet.
Remove power from the ECM.
Remove the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Install the replacement ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Download the flash file.
Connect the electronic service tool to the diagnostic connector.
Select "WinFlash" from the "Utilities" menu of the electronic service tool.
Select the downloaded flash file.
If necessary, use the electronic service tool to clear the rating interlock. To clear the rating interlock, enter the factory password when the electronic service tool is first connected. Activating the "Test ECM" mode will also clear the rating interlock.
Use the electronic service tool to program the parameters. Perform the following procedure.
If the "Copy Configuration" procedure was successful, use the "Copy Configuration, ECM Replacement" function to load the configuration file into the ECM. Note: During the following procedure, factory passwords may be required.
If the "Copy Configuration" procedure failed, configure the parameters individually. The parameters should match the parameters from step 3.
Check for logged diagnostic codes. Factory passwords are required to clear logged events.


Parts bearing Mariner:

32117
 
32117 BEARING, BALL - UPPER
7080508, 7085507
63742
 
63742 BEARING, BALL - LOWER
7031203GD, 7031207CD, 70404119D, 70432037D, 7045217, 7050200, 7050302ED, 7050412YD, 7050716, 7055207GD, 7060412ET, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
52168
 
52168 BEARING, NEEDLE
7070509, 7080508, 7085507, 7090529, 7115528, 7115529, 7140528, 7140629
62596A 1
 
62596A 1 BEARING ASSEMBLY. CRANKPIN
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
47270
 
47270 BEARING, NEEDLE - PISTON PIN
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7050716, 7050717, 7055207GD, 7055207HB, 7055207TF, 7
32898
 
32898 BEARING, ROLLER - DRIVE SHAFT
7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 71354120D, 7140528, 7140629, 7150453ND, 7150453PD
30895
 
30895 BEARING, ROLLER - FORWARD GEAR
7002201DK, 7050302ED, 7050412YD, 7055207GD, 7060412ET, 7075217CD, 7075312ND, 7075312SD, 7075524, 7075717, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7100412CD, 7100412NC, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7135412ED, 7135412H
Back to top