93495 Mariner BEARING, Roller, CRANKSHAFT


93495 BEARING, Roller, CRANKSHAFT Mariner 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200412PD, 7220727 BEARING
93495 BEARING, Roller, CRANKSHAFT Mariner
Rating:
93

Buy BEARING, Roller, CRANKSHAFT 93495 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Mariner entire parts catalog list:

Information:

The following background information is related to this procedure:Electronically Controlled Wastegate
Illustration 1 g03795243The engine has a turbocharger with an electronically controlled wastegate (1). Typically, the wastegate is a mechanical valve that is used in the turbocharger in order to regulate the intake manifold pressure to a set value.The control system for the electronically controlled wastegate precisely regulates the intake manifold pressure by using a wastegate regulator to control the wastegate.The required intake manifold pressure is calculated by the software that is contained in the ECM. The ECM uses the wastegate regulator to control the wastegate in order to provide the precise value of intake manifold pressure. The solenoid in the wastegate regulator is controlled by a PWM signal from the ECM.Suction Control Valve for the High-Pressure Fuel Pump
Illustration 2 g03795285The high-pressure fuel pump is equipped with a suction control valve (2). The suction control valve precisely controls the amount of fuel that enters the high-pressure fuel pump.The amount of fuel that is required is calculated by the software that is contained in the ECM. The solenoid in the suction control valve is controlled by a PWM signal from the ECM.
Illustration 3 g03812182
Schematic for the solenoid valves connected to the engine ECM
Illustration 4 g03812187
Pin locations on the P2 connector for the solenoid valves
(16) Wastegate regulator PWM signal
(24) Wastegate regulator return
(69) High pressure fuel pump suction control valve return
(77) High pressure fuel pump suction control valve PWM signal Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 ECM connector and the solenoids. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the solenoid connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the solenoids to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all of the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 20 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: An XXXX-5 diagnostic code is active.
Proceed to Test Step 3.
Result: An XXXX-6 diagnostic is active.
Proceed to Test Step 5.
3. Create a Short Circuit at the Harness Connector for the Solenoid
A. Turn the keyswitch to the OFF position.
B. Disconnect the


Parts bearing Mariner:

67923
 
67923 BEARING, Ball (LOWER)
7002201DK, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135417PD, 7135473GD, 7135473HD, 7135826, 7150413ED, 7150413HD, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413AD, 7175413PD, 7175413YD, 7175423HD, 7175629, 7200412PD, 7200473FD, 7200473GD, 720
88903
 
88903 BEARING, Roller
7135826, 7150629, 7175629
67445
 
67445 BEARING, Roller
7135826, 7150629, 7175629, 7200620
17514A 1
 
17514A 1 BEARING KIT
7031203GD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7115473JD, 71354120D, 7135473H
86637
 
86637 BEARING
7031203GD, 7031207LF, 7031312TB, 7041203GB, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7150629, 7175629, 7200620, 7250422PD, 7F25203JB, 7F25203LB
93496
 
93496 BEARING, Roller
7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200412PD, 7200620, 7220727
41429A 1
 
41429A 1 BEARING ASSEMBLY, DRIVE GEAR
7135417PD, 7135826, 7150453ND, 7150453PD, 7175412PD, 7220727
814103
BEARING
814103 BEARING
7150453PD, 7175412PD, 7200412PD
Back to top