99054M Mariner BEARING HOUSING (SEE NOTE #3)


99054M BEARING HOUSING (SEE NOTE #3) Mariner 7010209, 7015529 BEARING

Buy BEARING HOUSING (SEE NOTE #3) 99054M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Compatible models:

7010209   7015529   Mariner

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
D 9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the fuel injection pump.
Ensure that number one piston is at the top center position on the compression stroke. Refer to the Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Illustration 1 g01343058
Typical example
Ensure that Tooling (C) is installed in Hole (Y) in the front housing. Use Tooling (C) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the crankshaft during repairs.
Ensure that Tooling (B) is installed into Hole (X) in camshaft gear (1).
Ensure that shaft (9) on the fuel injection pump is clean, dry and free from damage.
Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install".
Ensure that the fuel pump gear is clean, dry and free from wear or damage. If necessary, replace the fuel pump gear.
Illustration 2 g01335384
Alignment of timing marks
Illustration 3 g01343060
Typical example
Illustration 4 g01440103
Install fuel pump gear (3) to shaft (9) of the fuel injection pump. Ensure that the timing Marks on gears (2) and (3) are in alignment and that the mesh of the gears is correct.
Install a new spring washer (10) and install nut (8) to shaft (9) of the fuel injection pump. Apply sufficient pressure to the fuel injection pump gear (3) in a counterclockwise direction in order to remove the backlash. Tighten nut (8) to a torque of 24 N m (17 lb ft). Unlock the fuel injection pump (5). In order to unlock the fuel injection pump, loosen locking screw (5) on the fuel injection pump. Rotate spacer (6) in order to allow locking screw (5) to tighten against the spacer. Tighten the locking screw against the spacer to a torque of 12 N m (106 lb in). This will prevent the locking screw from tightening against the shaft of the fuel injection pump.
Remove Tooling (B) and Tooling (C).
Tighten nut (8) to a torque of 90 N m (66 lb ft).
Use Tooling (D) to measure the backlash of gears (2) and (3). Ensure that the backlash for the gears is within specified values. Refer to Specifications, "Gear Group (Front)" for further information.
Lubricate the teeth of the gears with clean engine oil. End By:
Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".


Parts bearing Mariner:

82303M
 
82303M BEARING, UPPER
7010209, 7015207, 7015529
82321M
 
82321M BEARING, FORWARD GEAR
7010209, 7015529, 7020201, 7025200, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
83938M
 
83938M BEARING (LOWER)
7010209, 7015529
99030M
 
99030M BEARING SEE NOTE #3
7010209, 7015529
84043M
 
84043M BEARING HOUSING (SEE NOTE #4)
7010209, 7015529, 7060522
Back to top