41893M Mariner BOLT W/WASHER


41893M BOLT W/WASHER Mariner 7020201, 7025200, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7F75413TD BOLT
41893M BOLT W/WASHER Mariner
Rating:
48

Buy BOLT W/WASHER 41893M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

Mariner entire parts catalog list:

7020201 1981
7025200 1980
7025208CW 1994,1995,1996,1997,1998
7025500 1980
7026226 1986,1988
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992
7F75413TD 2005,2006

Information:

1. Disconnect connector (1). 2. Attach Tool (A) and fasten a hoist.3. Remove four bolts (3) and stack (2). The weight of the stack and hardware is 45 kg (99 lb). 4. Remove hose clamp (6).5. Remove five bolts (5) and support (4).6. Repeat Steps 4 and 5 for the other side of the engine. 7. Remove six bolts (7) that connect oil pan (8) to flywheel housing (9). Loosen the rest of the bolts that hold the oil pan in position. 8. Attach Tool (A) to the flywheel housing and a hoist. 9. Lift the end of the engine enough so a 1/2 ( in) Hardened Washer (10) can be installed on each side of the engine between the oil pan and the cylinder block.10. Install blocks under the oil pan to support the engine when the flywheel housing is removed. Lower the engine onto the blocks. 11. Remove twenty one bolts (11) and flywheel housing (9). The weight of the flywheel housing is approximately 91 kg (201 lb).Install Flywheel Housing
1. Install two 1/2 in-13 NC × 101 mm (4 in) Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (201 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts: a. Tighten bolts 1 through 20 in number sequence to a torque of 40 10 N m (30 7 lb ft).b. Tighten the 3/8" bolts in number sequence to a torque of 55 10 N m (41 7 lb ft). Tighten the 1/2" bolts in number sequence to a torque of 135 20 N m (100 15 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8. Repeat Step (7) for the other side of the engine. 9. Use Tool (A) to lift stack (2) in place. Install the stack to the engine with four bolts (3). 10. Connect connector (1).End By:a. install crankshaft rear seal and wear sleeveb. install all turbochargers


Parts bolt Mariner:

82405M
 
82405M BOLT
7002200, 7002207, 7003207, 7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008218EW, 7008226, 7008238, 7008248, 7008305, 7008425, 7010209, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207,
91725M
 
91725M BOLT
7002200, 7004201, 7005201, 7005207, 7008204, 7008208, 7008226, 7008238, 7008248, 7008305, 7010209, 7015327, 7015529, 7025200, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207PW, 7040208, 7040328, 7040716, 704
84211M
 
84211M BOLT
7010209, 7015307, 7015327, 7015529, 7025200, 7025207NW, 7025207PW, 7025500, 7028207, 7028527, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82938M
 
82938M BOLT
7028207, 7028527, 7040207, 7040507
84735M
 
84735M BOLT W/WASHER
7028527, 7030200, 7030205, 7030301
41839M
 
41839M BOLT (ELECTRIC)
7030320, 7048321, 7055324, 7055524, 7060522
42973
 
42973 BOLT, (M12 x 154)
7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075D73UY, 7090412TB, 7090412TD, 7090412TY, 7090412U
827077M
 
827077M BOLT
7025208CW
Back to top