75379 Mariner BOLT, THRU


75379 BOLT, THRU Mariner 70404119D, 7045217, 7050200, 7050716 BOLT
75379 BOLT, THRU Mariner
Rating:
23

Buy BOLT, THRU 75379 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

Mariner entire parts catalog list:

70404119D 1989,1990,1991,1992,1993,1994,1995,1996,1997
7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050716 1986

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Illustration 1 g01340072
Typical example
Disconnect the upper radiator hose from water temperature regulator housing (1) on the cylinder head.
Illustration 2 g01340075
Typical example
Remove the air inlet hose from inlet connection (3) on inlet manifold (2).
Follow Steps 4.a and 4.b in order to disconnect harness assembly (4) from coolant temperature sensor (5).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from coolant temperature sensor (5).
Follow Steps 5.a and 5.b in order to disconnect harness assembly (4) from boost pressure sensor (6).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from boost pressure sensor (6).
Follow Steps 6.a and 6.b in order to disconnect harness assembly (4) from inlet air temperature sensor (7).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from inlet air temperature sensor (7).
Remove all cable straps that secure harness assembly (4) to the cylinder head or to the inlet manifold. The harness assembly should be positioned in order to avoid causing an obstruction during the removal of the cylinder head.
Illustration 3 g01340077
Typical example
Loosen the tube clips for tube assembly (8). Remove tube assembly (8) for the fuel return from the cylinder head and from the transfer pump. Plug the port in the transfer pump with a new plug. Cap the tube assembly with new caps.
If the engine has a wastegate solenoid, loosen the tube clips for tube assembly (9). Remove tube assembly (9) from the wastegate solenoid and from the cylinder head. Plug the port in the wastegate solenoid with a new plug. Cap the tube assembly with new caps.
Illustration 4 g01340080
Typical example
Remove bolts (10). Remove bypass tube (11) from the cylinder head. Remove O-ring seals (12) and (13) from bypass tube (11).
Illustration 5 g01340081
Illustration 6 g01340083
Sequence for tightening the bolts for the cylinder head
Gradually loosen bolts (14) in the reverse numerical order to the tightening sequence. Refer to the illustration 6. Note: Follow the correct sequence in order to help prevent distortion of the cylinder head.
Remove bolts (14) from cylinder head (15).
Illustration 7 g01340086
Typical example
Attach a suitable lifting device (16) to cylinder head (15). Support the weight of the cylinder head. The weight of the cylinder head is approximately 66 kg (145.5 lb). Note: A spreader bar must be used in order to distribute the weight of the cylinder head during the lifting operation.
Use suitable lifting device (16) to carefully lift cylinder head (15) off the cylinder block. Note: Do not use a lever to separate the cylinder head from the cylinder block. Take care not to damage the machined surfaces of the cylinder head during the removal procedure.
Place the cylinder head on a surface that will not scratch the face of the cylinder head.


Parts bolt Mariner:

68298
 
68298 BOLT, (.375-16 x 3.250), BRACKET TO BOAT
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060507, 7060524, 7060528, 7070509, 7070520, 7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
66897
 
66897 BOLT, UPPER MOUNT TO SWIVEL PIN (7/16 X 5 1/4")
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
68576
 
68576 BOLT, THRU - PLATE TO END CAP
7050716, 7060312PC, 7060524, 7070509, 7070520
7733
 
7733 BOLT SET, THRU - PLATE AND FRAME TO RESERVOIR
7045217, 7050200, 7050716, 7060312PC, 7060524, 7070520, 7080629, 7090520, 7115520
8855
 
8855 BOLT, THRU - END CAP TO END PLATE (1/4-28)
7050716, 7060312PC, 7060524, 7070520, 7075524, 7080629
89673
 
89673 BOLT, TRANSOM BRACKET TO TRANSOM (5")
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070520, 7080629, 7090520, 7115520
31830
 
31830 BOLT, (.375-24 x 1.75)
7045217, 7050200, 7050716, 7060312PC, 7060524, 7090524, 7115520, 7150629, 7200620, 7250422PD
95686
 
95686 BOLT, THRU
7050302ED, 7050412YD, 7050716, 7050717, 7060312PC, 7060412ET, 7060524
Back to top