82453M Mariner BOLT, ATTACHING...


82453M BOLT, ATTACHING... Mariner 7008208, 7008238, 7008247, 7008248, 7008305, 7015207, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030301, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7060507, 70605 BOLT
82453M BOLT, ATTACHING... Mariner
Rating:
43

Buy BOLT, ATTACHING... 82453M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Mariner entire parts catalog list:

7008208 1978
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7015207 1977
7015327 1987
7020201 1981
7025200 1980
7025207NW 1988
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030301 1981
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040208 1978
7040328 1978,1980
7040507 1987
7040716 1986
7048207 1977
7048227 1977
7048321 1981
7060507 1977
7060522 1982
7060528 1978

Information:

Note: This procedure is for the removal of the engine oil pump on engines that are not equipped with a balancer. Refer to Disassembly and Assembly, "Balancer - Remove" for information on the removal of the engine oil pump for engines that are equipped with a balancer.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01255703
Typical example
Remove bolts (1) and suction pipe (2).
Remove the gasket from the suction pipe.
Remove bolts (5). Remove the assembly of the engine oil pump (3) from the cylinder block.
If necessary, remove pressure relief valve (4) from the housing of engine oil pump (3). Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install".
Illustration 2 g01470295
Typical example
If necessary, remove bolts (9) and front cover assembly (6). Remove outer rotor (7) from the housing of engine oil pump (3). Note: Do not remove dowels (8) and (10) from the housing of the engine oil pump unless the dowels are damaged.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1 Note: This procedure is for the installation of the engine oil pump on engines that are not equipped with a balancer. Refer to Disassembly and Assembly, "Balancer - Install" for information on the installation of the engine oil pump for engines that are equipped with a balancer.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If any of the parts on the engine oil pump are worn or damaged, the entire pump must be replaced.
Ensure that all components of the engine oil pump are clean and free from wear or damage. Check the clearance between the outer rotor of the oil pump and the oil pump body. Check the clearance between the outer rotor and the inner rotor. Check the end play of the rotor. Refer to Systems Operation, Testing and Adjusting, "Engine Oil Pump - Inspect". Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.
Illustration 3 g01470295
Typical example
If necessary, lubricate the internal components of the assembly of the engine oil pump with clean engine oil. Install outer rotor (7) and front cover (6) to the housing of engine oil pump (3). Install bolts (9). Tighten the bolts to a torque of 9.5 N m (84 lb in).
Illustration 4 g01255703
Typical example
If necessary, install pressure relief valve (4). Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install" for further information.
Ensure that dowel (8) and dowel (10) are correctly located in the housing of engine oil pump (3). Position the assembly of the engine oil pump onto the cylinder block. Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the holes in the cylinder block.
Install bolts (5). Tighten the bolts to a torque of 44 N m (32 lb ft).
Install suction pipe (2) and a new gasket to the assembly of the engine oil pump.
Install bolts (1). Tighten the bolts to a torque to 22 N m (16 lb ft).
Use Tooling (A) in order to check the backlash between the idler gear of the oil pump and the crankshaft gear. Refer to Specifications, "Gear Group - Front" for further information. End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".


Parts bolt Mariner:

91725M
 
91725M BOLT
7002200, 7004201, 7005201, 7005207, 7008204, 7008208, 7008226, 7008238, 7008248, 7008305, 7010209, 7015327, 7015529, 7025200, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207PW, 7040208, 7040328, 7040716, 704
80429M
 
80429M BOLT, CHOKE CABLE...
7008238, 7008247
82455M
82465M
 
82465M BOLT, DRIVESHAFT HOUSING ATTACHING
7015207, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7060507, 7060522, 7060528
82407M
 
82407M BOLT
7015307, 7015327, 7020201, 7025200, 7025500, 7028207, 7028527
82477M
 
82477M BOLT, TRIM TAB ATTACHING
7025207PW, 7025500, 7026226, 7028207, 7028527, 7030205, 7030320
82448M
 
82448M BOLT
7025207NW, 7028207, 7028527, 7040207, 7040208, 7040507, 7048207, 7048227, 7048321, 7060507, 7060528
96371M
BOLT (THRU THRU )
96371M BOLT (THRU THRU )
7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7040202, 7040206, 7040706, 7040716
Back to top