826958M Mariner BOLT


826958M BOLT Mariner 7008218EW, 7008425, 7025208CW, 7F75411JD, 7F75412RD BOLT
826958M BOLT Mariner
Rating:
83

Buy BOLT 826958M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Compatible models:

Mariner entire parts catalog list:

7008218EW 1996,1998
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997
7025208CW 1994,1995,1996,1997,1998
7F75411JD 2000,2001,2002,2003
7F75412RD 2004,2005

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
1/2 inch - UNF by 4 inch 2 Start By:
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
If necessary, remove the air starting motor. Refer to Disassembly and Assembly, "Air Starting Motor - Remove" for the correct procedure.
Remove the generator. Refer to Disassembly and Assembly, "Generator - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01528438
Typical Example
Remove bolts (2) from Position (X) on flywheel (1).
Install Tooling (A) in Position (X) on flywheel (1).
Install a suitable lifting device on flywheel (1). Support the weight of the flywheel. The weight of the flywheel (1) is approximately 70 kg (154 lb).
Remove remaining bolts (2).
Use the lifting device to remove the flywheel from the engine.
Illustration 2 g01528441
Typical example
Inspect flywheel (1) and ring gear (3) for wear or damage. Replace any worn components or damaged components.
To remove flywheel ring gear (3), follow step 7.a and step7.b.
Place the flywheel assembly on a suitable support.
Use a hammer and a punch to remove ring gear (3) from flywheel (1).Note: Identify the orientation of the teeth on the flywheel ring gear.Installation Procedure
Illustration 3 g01528461
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c to install ring gear (3) to flywheel (1).
Identify the orientation of teeth (4) on new ring gear (3).Note: The chamfered side of ring gear teeth (4) must face toward the starting motor when the flywheel is installed. Identify the orientation of ring gear (3) on the flywheel for the correct positioning when the new ring gear is installed.
Heat flywheel ring gear (3) to a maximum temperature of 250 °C (482 °F) prior to installation.Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
Illustration 4 g01528438
Typical Example
Install a suitable lifting device on flywheel (1). The weight of the flywheel (1) is approximately 70 kg (154 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
Install bolts (2) to flywheel (1).
Remove Tooling (A) and install remaining bolts (2) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information.End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
If necessary, install the air starting motor. Refer to Disassembly and Assembly, "Air Starting Motor - Install" for the correct procedure.
Install the generator. Refer to Disassembly and Assembly, "Generator - Install" for the correct procedure.


Parts bolt Mariner:

84368M
 
84368M BOLT
7002200, 7002207, 7003207, 7005207, 7005227, 7008218EW, 7008425, 7040208PW, 7115F13UF, 7F75413TD
95554M
 
95554M BOLT
7025208CW, 7028527, 7030200, 7030205, 7030320
827043M
 
827043M BOLT
7008218EW, 7008425, 7025208CW, 7040208PW
19247M
 
19247M BOLT
7008218EW, 7008425
827162M
 
827162M BOLT
7008218EW, 7008425
804124
 
804124 BOLT
7025208CW, 7040208PW, 7115F13UF, 7F75411JD, 7F75412RD, 7F75413TD
826899M
 
826899M BOLT
7025208CW
825501
BOLT
825501 BOLT
7F08203HF, 7F08261DF, 7F15201GD, 7F75411JD
Back to top