84313M BOLT Mariner
7002200, 7010209, 7015529, 7020201, 7025200, 7025208CW, 7025500, 7028207, 7028527, 7030200, 7030205, 7030320, 7040208PW, 7040706, 7040716
BOLT
Price: query
Rating:
Compatible models:
Mariner entire parts catalog list:
- CHOKE-MAGNETO CONTROL AND FUEL COCK » 84313M
- FLYWHEEL MAGNETO » 84313M
- C.D.I. MAGNETO » 84313M
- FLYWHEEL (M-020025 ML-316415 E-251060 EL-551615 & BELOW) » 84313M
- CDI MAGNETO (M-020026 ML-316416 E-251061 EL-551616 & UP) » 84313M
- C.D.I. MAGNETO » 84313M
- FLYWHEEL MAGNETO » 84313M
- C.D.I. - MAGNETO » 84313M
- ELECTRICAL » 84313M
- FLYWHEEL MAGNETO » 84313M
- C.D.I. - MAGNETO » 84313M
- THROTTLE CONTROL » 84313M
- THROTTLE CONTROL » 84313M
- C.D.I MAGNETO ASSEMBLY » 84313M
- C.D.I MAGNETO ASSEMBLY » 84313M
- C.D.I. MAGNETO ASSEMBLY » 84313M
- C.D.I MAGNETO » 84313M
- STEERING HANDLE » 84313M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 84313M
- STEERING HANDLE » 84313M
- STEERING HANDLE » 84313M
Information:
Illustration 1 g03389877
Typical example
Use a suitable tool in order to remove temperature sensor (6) from the Clean Emissions Module (CEM).
Remove bolt (4) and the washer from the harness assembly clip (5).
Disconnect harness assembly (9) from harness assembly (10).
Cut cable straps (11) from harness assembly (10). Note: Ensure that all cable straps are removed for the harness assembly.
Remove bolts (1) and spacers (2) from bracket (3).
Remove bolts (8) and spacers (7) from bracket (3).
Remove bracket (3) from the CEM bracket.
Remove bolts (13) and spacers (14) (not shown) from bracket (12).
Illustration 2 g03389883
Use a suitable tool in order to remove temperature sensor (17) from the CEM.
Remove bolts (16) and spacers (15) from bracket (12).
Remove bracket (12) from bracket (18) for the CEM.
Illustration 3 g03389963
Make temporary marks on harness assembly (10) for installation purposes.
Make temporary mark on clip (5) for installation purposes. Remove clip (5) from harness assembly (10).
Cut cable straps (19) that secure harness assembly (10) to bracket (12). Note: Ensure that all cable straps are removed for the harness assembly.
Remove harness assembly (10) from bracket (12). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Bostik Pure Nickel
Anti-Seize Compound 1
Ensure that all components of the temperature sensor are clean and free from wear and damage. If any component of the temperature sensor is worn or damaged, the assembly of the temperature sensor must be replaced.
Illustration 4 g03389963
Position harness assembly (10) onto bracket (12). Ensure that harness assembly is correctly orientated onto the bracket.
Install new cable straps (19) that secure harness assembly (10) to bracket (12). Note: Ensure that the cable straps meet the Original Equipment Manufacturer (OEM) specification.
Install clip (5) from harness assembly (10). Ensure that the clip is correctly orientated.
Illustration 5 g03389883
Position bracket (12) onto bracket (18) for the CEM.
Install bolts (16) and spacers (15) from bracket (12) finger tight.
Apply Tooling (A) to the threads of temperature sensor (17).
Use a suitable tool in order to install temperature sensor (17) to the CEM. Tighten the temperature sensor to a torque of 45 N m (33 lb ft). Ensure that the temperature sensor does not come into contact with any part on the CEM.
Illustration 6 g03470560
Illustration 7 g03389877
Install bolts (13) and spacers (14) (not shown) to bracket (12) finger tight.
Tighten bolts (13) and bolts (16) to a torque of 12 N m (106 lb in).
Apply Tooling (A) to the threads of temperature sensor (6). Use a suitable tool in order to install temperature sensor (6) to the CEM.
Install bolt (4) and the washer to the harness assembly clip (5) hand tight. Ensure that the clip is correctly positioned.
Tighten the temperature sensor to a torque of 45 N m (33 lb ft). Ensure that the temperature sensor does not come into contact with any part on the CEM.
Tighten bolts (4) to a torque of 12 N m (106 lb in).
Position bracket (3) onto the CEM bracket.
Install bolts (1) and spacers (2) to bracket (3). Tighten the bolts to a torque of 12 N m (106 lb in).
Position harness assembly (10) onto bracket (3).
Install new cable straps (11) to harness assembly (10). Note: Ensure that cable straps meet the OEM specification.
Connect harness assembly (9) to harness assembly (10).
Turn the battery disconnect switch to the ON position.
Parts bolt Mariner:
82449M
82449M BOLT, LOWER OIL SEAL HOUSING ATTACHING...
7008238, 7008247, 7015207, 7028207, 7028527, 7048207, 7048227
82464M
82464M BOLT, DRIVESHAFT HOUSING ATTACHING
7015207, 7015307, 7015327, 7025200, 7025207NW, 7025500, 7028527, 7030200, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7060507, 7060522, 7060528
82471M
81146M
81711M
81711M BOLT
7020201, 7025200, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
81712M
84779M
82472M