8M0051401 BOLT, Stainless Steel Mariner
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
BOLT
Price: query
Rating:
Mariner entire parts catalog list:
- TILLER HANDLE CONVERSION KIT, MANUAL - 8M0051061 » 8M0051401
- TILLER HANDLE CONVERSION KIT, ELECTRIC - 8M0051062 » 8M0051401
- TILLER HANDLE CONVERSION KIT, MANUAL - 8M0051061 » 8M0051401
- TILLER HANDLE CONVERSION KIT, ELECTRIC - 8M0051062 » 8M0051401
- TILLER HANDLE CONVERSION KIT, MANUAL - 8M0051061 » 8M0051401
- TILLER HANDLE CONVERSION KIT, ELECTRIC - 8M0051062 » 8M0051401
- TILLER HANDLE CONVERSION KIT, MANUAL - 8M0051061 » 8M0051401
- TILLER HANDLE CONVERSION KIT, ELECTRIC - 8M0051062 » 8M0051401
Information:
1. Remove shaft (2). Remove pin (1) from shaft.2. Remove pins (3) from the flyweights. Remove flyweights (4). 3. Remove ring, races (6) and bearing from the riser (follower) (5). 4. Remove cover (7) and spring (8) from governor housing. There is force on the cover from the spring.5. Remove seal (9) from cover.6. Remove cover (10) for the low and high idle adjustment. 7. Remove locknut and screw (13) for the high idle adjustment.8. Remove bolt (15) and washers for the low idle adjustment.9. Remove spring (16) and guide.10. Remove pin (14) and plate (11).11. Remove shaft (12) from the housing. 12. Remove pin (18) and two spacers (17) from shaft. Earlier fuel systems have a ball in place of spacers (17) and pin (18). 13. Remove shaft (19) from the governor housing.14. Remove washer (20) and levers (21) and (22) from governor housing. 15. Remove cover (23) from governor housing. 16. Remove seal (25) and bearing.17. Remove seals (24) and 26) from governor housing.Assemble Governor
1. Install the bearing and lip type seal in the governor housing with tooling (A). The lip of the seal must be toward the bearing.2. Install lip type seal (1) in the governor housing with tooling (A). The lip of seal must be toward inside of housing.3. Install lip type seal (2) in the governor housing with tooling (B). The lip of seal must be toward the inside of the governor housing. Put lubricant that is to be sealed on the lip of all the seals. 4. Install shaft (3) in the governor housing. 5. Install plates (4), spacers (8) and pin (7) on shaft (5).6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and the guide.10. Install bolts (12) and washer for the low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push the plate and pin (11) over toward bolt (12) and tighten the bolt.12. Install the lip type seal in the cover with tooling (B). The lip of the seal must be toward the inside of the governor housing and installed to a depth of 1.50 1.50 mm (.059 .059 in.) from the outside surface. Put lubricant that is to be sealed on the lip of the seal. 13. Install cover (16) for the idle adjustment screws.
Spring (15) must be installed with the end of the spring as shown in illustration A 10291X3.
14. Install spring (15) in the cover. Install cover (14) on the governor housing. 15. Install bearing (19) between races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.END BY:a) connection of governor to fuel injection pump housing
1. Install the bearing and lip type seal in the governor housing with tooling (A). The lip of the seal must be toward the bearing.2. Install lip type seal (1) in the governor housing with tooling (A). The lip of seal must be toward inside of housing.3. Install lip type seal (2) in the governor housing with tooling (B). The lip of seal must be toward the inside of the governor housing. Put lubricant that is to be sealed on the lip of all the seals. 4. Install shaft (3) in the governor housing. 5. Install plates (4), spacers (8) and pin (7) on shaft (5).6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and the guide.10. Install bolts (12) and washer for the low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push the plate and pin (11) over toward bolt (12) and tighten the bolt.12. Install the lip type seal in the cover with tooling (B). The lip of the seal must be toward the inside of the governor housing and installed to a depth of 1.50 1.50 mm (.059 .059 in.) from the outside surface. Put lubricant that is to be sealed on the lip of the seal. 13. Install cover (16) for the idle adjustment screws.
Spring (15) must be installed with the end of the spring as shown in illustration A 10291X3.
14. Install spring (15) in the cover. Install cover (14) on the governor housing. 15. Install bearing (19) between races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.END BY:a) connection of governor to fuel injection pump housing
Parts bolt Mariner:
16125 1
16125 1 BOLT (FRONT)
7002201HB, 7002201UB, 7003201BK, 7004201HB, 7004201UB, 7004211SK, 7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F02201ZK, 7F042016B, 7F04201JB
803509 2
825702002
825702002 BOLT, Stainless Steel
7015203UL, 7040203UL, 7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F02201ZK, 7F08201TB
823042038
823042040
16695006
16695006 BOLT
7025207UL, 7025217UL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
855677003
823042049