828528 Mariner BRACKET


828528 BRACKET Mariner 7F41452KD, 7F50352HD, 7F50412DD BRACKET
828528 BRACKET Mariner
Rating:
63

Buy BRACKET 828528 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$38.89
 

22-11-2023

-: -
ALEXRIMS 828528 Hub Parts, Silver, One Size Bearing Kit for ALX320 COMP/295R/FOLEX, Front
For ALX320 COMP/295R/FOLEX
$112.89
 

10-05-2022

-: -
Replacement For Ezgo/Cushman/Textron 828528
Replacement For Ezgo / Cushman / Textron 828528 || Unit per sale:1
$15.92
 

05-08-2019
15 Hundredths Pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver Oem Part # 828528 Bracket
Number on catalog scheme: 25
 

Compatible models:

Mariner entire parts catalog list:

7F41452KD 2001
7F50352HD 1999,2000
7F50412DD 1995,1996,1997,1998

Information:

1. Remove six bolts (1) and washers from rocker shaft assembly.2. Remove rocker shaft assembly (2) from the cylinder head.3. Remove push rods (4) from engine.4. Loosen adjusting screws (3) on the rocker arms for valve clearance. This will prevent a bent valve or push rod at installation. The following steps are for the installation of the rocker shafts and push rods.5. Install push rods (4). The O-ring seal in the rear support must be installed new each time the bolt is removed from the rear support bracket.6. Put rocker shaft assembly (2) in position on cylinder head.
Make sure the dowels on each end of the rocker shaft assembly are in alignment with the holes in the cylinder head.
7. Put 2P2506 Thread Lubricant on the threads of all rocker shaft mounting bolts except bolt (10). Install bolts in the rocker shaft assembly.8. Tighten the bolts for the rocker shaft as follows:
3306 Tightening Sequence
3304 Tightening Sequencea. Tighten all the bolts in number sequence to a torque of 155 N m (115 lb.ft.).b. Tighten all the bolts again in number sequence to a torque of 250 17 N m (185 13 lb.ft.).c. Last, tighten bolts again in number sequence (hand tighten only to a torque of 250 17 N m (185 13 lb.ft.).9. The assembled length of springs at both ends of rocker shaft must be 1.50 0.25 mm (.059 .010 in.). Remove or install washers behind springs to change the assembled length of the springs.10. Make adjustments until the intake valve clearance is .038 mm (.015 in.) and the exhaust valve clearance is 0.64 mm (.025 in.). See the topic, Valve Clearance Setting in Testing And Adjusting. Tighten the locknuts (2) for the adjusting screws (1) to a torque of 29 7 N m (21 5 lb.ft.).End By:a. install valve cover.Disassemble And Assemble Rocker Shaft
Start By:a. remove rocker shaft and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washer (3) from each end of rocker shaft. Remove rocker arm (2). 3. Remove pin from rear support bracket with a hammer and punch. Remove rear support bracket (7) from shaft.4. Remove remainder of rocker arms, springs, washers and brackets.5. Remove plugs from each end of the shaft if necessary. The following steps are for the assembly of the rocker shaft. 6. Install rocker arms (2), brackets (8), washers (5) and springs (4) on the rocker shaft.7. Install rear support bracket (7) on rocker shaft. Make sure hole in rear support bracket is in alignment with hole in rocker shaft.8. Install pin (9) through bracket and shaft with a hammer.9. Pin (9) must extend 9.60 mm (.378 in.) above the bracket.10. Install O-ring seal (1) in the rear support bracket. Install rocker arm (2), washer, spring, washer and retainer ring on the rocker shaft.11. Install the plugs in each end of the rocker shaft if they were removed.End By:a. install rocker shaft and push rods


Parts bracket Mariner:

18173
 
18173 BRACKET
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412E
822426 1
 
822426 1 BRACKET
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 7A30302LB, 7A40302UD, 7A40312UZ, 7A41412LB, 7A41452UZ, 7A60412ZZ, 7A60452IZ, 7E60452ZB, 7F08203HF, 7F08261DF, 7F25201GD, 7F25203JB, 7F25203LB, 7F30203HD, 7F30203LB, 7F40203UD, 7F40213UZ, 7F40452K
827631
BRACKET
827631 BRACKET
7F41452KD, 7F50352HD, 7F50412DD
830294
834791
 
834791 BRACKET
7F41452KD, 7F50352HD, 7F50412DD
809557
856040
BRACKET
856040 BRACKET
7A30302LB, 7A41412LB, 7F25201GD, 7F25203JB, 7F25203LB, 7F30203HD, 7F30203LB, 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD
830294T 1
 
830294T 1 BRACKET
7F30203HD, 7F30203LB, 7F40203UD, 7F40203ZZ, 7F40213UZ, 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD, 7F50352HD
Back to top