43052A 1 Mariner BUSHING ASSEMBLY, SHIFT SHAFT


43052A 1 BUSHING ASSEMBLY, SHIFT SHAFT Mariner 7075312ND, 7075312SD, 7075717, 7100412NC BUSHING
43052A 1 BUSHING ASSEMBLY, SHIFT SHAFT Mariner
Rating:
58

Buy BUSHING ASSEMBLY, SHIFT SHAFT 43052A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

Compatible models:

Mariner entire parts catalog list:

7075312ND 1988,1989
7075312SD 1990,1991,1992,1993
7075717 1987,1989
7100412NC 1988,1989,1990,1991,1992,1993

Information:

Start By:a. remove expansion tank & heat exchangerb. remove crankshaft pulleyc. remove oil pan 1. Remove bolts (7) and front support (6). Remove water lines (1) and (3) from the exhaust manifolds. Remove tachometer drive adapter (2). Remove elbow (4).2. Remove elbow (5) and sea water pump (8). 3. Remove the clamps from the water sleeves in each cylinder head. Push the sleeves into the timing gear cover with tool (A) and a screwdriver.4. Remove the bolts that hold the timing gear cover to the cylinder block. Be sure to remove the bolt that is behind elbow (4). Put identification of the bolts as to their location for use at installation.
Be extra careful not to cause damage of the crankshaft front seal during removal and installation of the timing gear cover.
5. Install two 7/16"-14 NC forged eyebolts in the timing gear cover. Fasten a hoist and remove timing gear cover (9) and the oil pump from the dowels on the cylinder block. The weight of the cover and pump is 61 kg (136 lb). The following steps are for installation of the timing gear cover and oil pump.6. Clean the contact surfaces of the cylinder block and timing gear cover. Install the timing gear cover gasket on the cylinder block. Make sure the water sleeves are installed in the timing gear cover. Put oil or grease on the seals for easier installation.7. Install two 7/16"-14 NC forged eyebolts in the timing gear cover. Fasten a hoist and put the timing gear cover (9) and the oil pump in position on the engine. Make sure the oil pump gear and crankshaft gear are in alignment.8. Install the bolts that hold the cover in place.9. Push the water sleeves into the cylinder heads with tool (A) and a screwdriver. Install the clamps to hold the water sleeves.10. Put front support (6) in position and install bolts (7).11. Install elbow (4) and the bolts that hold it to the timing gear cover. Connect water lines (1) and (3) to the exhaust manifolds.12. Install tachometer drive adapter (2) and the bolts.13. Install elbow (5) and sea water pump (8).End By:a. install oil panb. install crankshaft pulleyc. install expansion tank & heat exchangerRemove & Install Timing Gear Cover & Oil Pump (Industrial Engine)
Start By:a. remove oil panb. remove crankshaft pulley 1. Remove tube (1). Remove belt adjuster (2) and fan drive adapter (3). 2. Remove air compressor tube (5) and belt adjuster (4). 3. Remove bolts (8) and support (9).4. Remove nuts (7) and tachometer drive adapter (6). 5. Loosen clamp (10), and disconnect hose (11) from the timing gear cover. 6. Remove clips (13) and disconnect three lines (12). 7. Remove clips (14) from the water sleeves. 8. Push water sleeves (15) into the front cover with tool (A). 9. Remove two bolts (16), connector (17) and the gasket behind it. 10. Remove bolts (18), elbow (19) and the gasket behind it. 11. Remove bolt (20) and disconnect clamp (21).
Be extra careful not to cause damage to the crankshaft front seal during removal and installation of the timing gear cover.
12. Install tooling (B) and a hoist on the front cover. Remove all the bolts that hold the timing gear cover to the cylinder block. Remove cover (22) and the oil pump. The weight of the timing gear cover and oil pump is 62 kg (136 lb). The following steps are for installation of the timing gear cover and oil pump.13. Clean the contact surfaces of the cylinder block and timing gear cover. Install the timing gear cover gasket on the cylinder block. Make sure the water sleeves are installed in the timing gear cover. Install the timing gear cover gasket on the cylinder block.14. Install tooling (B) on timing gear cover (22).15. Put the cover in position, and align the dowels and their respective holes. Install the bolts that hold timing gear cover (22) to the cylinder block.16. Connect clamp (21) and install bolt (20).17. Install the gasket, elbow (19), and bolts (18).18. Install the gasket, connector (17), and bolts (16).19. Push water sleeves (15) into the cylinder heads with tool (A).20. Install clips (14) on the water sleeves.21. Connect three lines (12), and install clips (13) that hold them.22. Install hose (11) and clamp (10).23. Put engine support (9) in position, and install bolts (8).24. Put tachometer drive adapter (6) in position, and install nuts (7).25. Install belt adjuster (4) and air compressor tube (5).26. Install fan drive adapter (3) and belt adjuster (2).27. Install tube (1).End By:a. install crankshaft pulleyb. install oil pan


Parts bushing Mariner:

69132
 
69132 BUSHING,PIVOT SHAFT
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075217CD, 7075312ND, 7075312SD, 7075524, 7075717, 7080508, 7090524, 7090529, 7100412NC, 7115520, 7115528, 7115529, 7140528, 7140629
818764
 
818764 BUSHING
7002201DK, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075D73UY, 7075D73ZY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7090D73RD, 7100412CD, 7100412H
48237
 
48237 BUSHING, NYLON - SHIFT LEVER (3/8"I.D.)
70404119D, 7045217, 7050200, 7050302ED, 7050412YD, 7050716, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 707
48475
 
48475 BUSHING, NYLON - SHIFT ROD (1/4" I.D.)
7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7045217, 7050200, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7050716, 7055207GD, 705
821207
 
821207 BUSHING
7002201DK, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075D73UY, 7075D73ZY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7090D73RD, 7100412CD, 7100412H
52151
 
52151 BUSHING
7075312ND, 7075312SD, 7075717
14395
 
14395 BUSHING, HOUSING SCREW
7075312ND, 7075312SD, 7075717, 7100412NC
93248 1
BUSHING
93248 1 BUSHING
7002201DK, 7020201NC, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217U
Back to top