81946M Mariner BUSHING, CAM


81946M BUSHING, CAM Mariner 7008204, 7008208, 7008226, 7010209, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7 BUSHING
81946M BUSHING, CAM Mariner
Rating:
48

Buy BUSHING, CAM 81946M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008226 1986
7010209 1979,1983,1984,1985,1986
7015307 1977
7015327 1987
7015529 1979
7020201 1981
7025200 1980
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025208CW 1994,1995,1996,1997,1998
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040208 1978
7040328 1978,1980
7040507 1987
7040706 1986,1990,1992
7040716 1986
7048207 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 237-9608 Mounting Bar 2
B 376-8697 Guide Stud
5/8 - 11 by 36 inch
(1) 2
8T-4122 Hard Washer 4
6V-4803 Thrust Bearing 4
4K-0367 Full Nut 8
C - Loctite Graphite Anti-Seize -
F 221-8647 Seal Installer Gp 1
G - 2-7/8 inch Vented Plug 1
- 2-3/4 inch Vented Plug 1
- 2-1/8 inch Vented Plug
(2) 2
- 1-7/8 inch Vented Plug
(3) 2
5P-3501 Adapter 2
3J-1907 O-Ring Seal 2
2D-7325 Pipe Tee 2
8T-0853 Pressure Gauge 2
4C-7121 Pipe Nipple 2
4C-7090 Valve 2
4C-7158 Fitting 2
(1) Cut 376-8697 guide studs to 18 inch lengths. Four 18 inch guide studs are required.
(2) Use with 201-6758 Sea Water Heat Exchanger Gp.
(3) Use with 290-3990 Sea Water Heat Exchanger Gp.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals and the seals for wear or for damage. Replace the components, if necessary.
Illustration 1 g02718886
Install hose connector (16) on filler neck (17). Install O-ring seal (18) on the filler neck.
Position filler neck (17) on the frame assembly. Install bolts (15).
Install pressure cap (14).
Illustration 2 g02718864
Use Tooling (F) to install lip seal (13) in the frame assembly.
Illustration 3 g02718840
Install inserts (12).
Install elbows (10) and zinc rods (11). Ensure that elbows (10) are in the proper orientation.
Install seals (9) in elbows (10).
Install Tooling (B) and Tooling (A) in the frame assembly. Ensure that Tooling (B) and Tooling (A) are securely installed. Apply Tooling (C) to the threads of the nut and the threads of the guide stud prior to installation.
Illustration 4 g02145556
Position the new seal on the heat exchanger plate. Install tabs (X) of the seal into the slots of heat exchanger plate (8).Note: Use a new seal on the heat exchanger plates for the fuel.
Illustration 5 g06015845Note: Type 1 heat exchangerNote: Do not reuse the old gasket.Note: Heat Exchanger Plate (Y) and Heat Exchanger Plate (Z) are identical. The orientation of the dimple (one dimple) on the heat exchanger plate is critical during the assembly of the heat exchanger plates. Heat Exchanger Plate (Y) and Heat Exchanger Plate (Z) are for the jacket water in the heat exchanger.Note: Heat Exchanger Plate (S) and Heat Exchanger Plate (T) are identical. The orientation of the dimples (two dimples) on the heat exchanger plate is critical during the assembly of the heat exchanger plates. Heat Exchanger Plate (S) and Heat Exchanger Plate (T) are for the fuel cooler in the heat exchanger.Note: Heat Exchanger Plate (W) has a notch that is stamped in the heat exchanger plate. The notch identifies the port that is blocked to prevent coolant flow. Heat Exchanger Plate (W) is installed to separate the jacket water from the fuel. The orientation of the notch and dimples (two dimples) on the heat exchanger plate is critical during the assembly of the heat exchanger plates.Note: Heat Exchanger Plate (P) has a notch that is stamped in the heat exchanger plate. The notch identifies the port that is blocked to prevent coolant flow. Heat Exchanger Plate (P) is installed against the front frame. The orientation of the notch and dimples (two dimples) on the heat exchanger plate is critical during the assembly of the heat excha


Parts bushing Mariner:

81056M
 
81056M BUSHING, PIVOT SHAFT...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
80227M
 
80227M BUSHING, PANEL ATTACHING...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7028207, 7028527
81960M
 
81960M BUSHING, PIVOT SHAFT-UPPER
7015207, 7015307, 7015327
81956M
 
81956M BUSHING, PIVOT SHAFT-LOWER
7015207, 7015307, 7015327
81963M
81950M
 
81950M BUSHING
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324
83883M
 
83883M BUSHING, SHIFT CAM
7040202, 7040206, 7040208, 7040328, 7040706, 7040716
41313M
 
41313M BUSHING
7040206, 7040207PW, 7040208PW, 7040706, 7040716, 7048321, 7055324, 7055524, 7060522
Back to top