83310M Mariner COLLAR


83310M COLLAR Mariner 7010209, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320 COLLAR
83310M COLLAR Mariner
Rating:
18

Buy COLLAR 83310M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979
7020201 1981
7025200 1980
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025208CW 1994,1995,1996,1997,1998
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992

Information:


Illustration 1 g00642016
Schematic for the accelerator pedal position sensor
Test Step 1. MONITOR THE STATUS FOR THE "ACCELERATOR PEDAL POSITION"
Turn the keyswitch to the OFF position.
Connect Cat ET to the service tool connector.
Turn the keyswitch to the ON position.
Access the status for the "Accelerator Pedal Position".
While the status is monitored, depress the accelerator pedal and release the accelerator pedal. The correct status for the "Accelerator Pedal Position" is 100 percent when the accelerator is fully depressed. The correct status for the "Accelerator Pedal Position" is less than 5 percent when the accelerator is fully released.
Turn the keyswitch to the OFF position. Expected Result:The correct status for the "Accelerator Pedal Position" is being reported by Cat ET.Results:
OK - The correct status for the "Accelerator Pedal Position" is being reported by Cat ET.Repair: The accelerator pedal position sensor is operating correctly. There may be an intermittent electrical problem in the circuit for the accelerator pedal position sensor. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".Verify that the engine is not in PTO mode. PTO mode may cause the accelerator pedal position sensor to be ignored.Verify that all required parameters are programmed. Certain unprogrammed parameters may cause the engine to be limited to low idle. Refer to Troubleshooting, "System Configuration Parameters".If a diagnostic code that is related to the accelerator pedal position sensor is still active, proceed to Test Step 2.
Not OK - The correct status for the "Accelerator Pedal Position" is not being reported by Cat ET. The accelerator pedal position sensor is not operating correctly. Proceed to Test Step 2.Test Step 2. MONITOR THE DUTY CYCLE
Turn the keyswitch to the ON position.
Access the following display screen in order:
"Service"
"Calibrations"
"Monitor Throttle Position Sensor"
While the duty cycle is being monitored, depress the accelerator pedal and release the accelerator pedal. The correct duty cycle is 10 percent to 22 percent when the accelerator pedal is released. The correct duty cycle is 75 percent to 90 percent when the accelerator pedal is depressed.
Turn the keyswitch to the OFF position. Expected Result:Cat ET reports that the duty cycle is correct.Results:
OK - Cat ET is reporting the correct duty cycle for the sensor.Repair: The duty cycle is within the specified range. There may be an intermittent electrical problem in the circuit for the accelerator pedal position sensor. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".Verify that the engine is not in PTO mode. PTO mode may cause the accelerator pedal position sensor to be ignored.Verify that all required parameters are programmed. Certain unprogrammed parameters may cause the engine to be limited to low idle. Refer to Troubleshooting, "System Configuration Parameters".STOP
Not OK - Cat ET is not reporting the correct duty cycle for the sensor. The duty cycle is not within the range. Proceed to Test Step 3.Test Step 3. INSPECT THE ELECTRICAL CONNECTORS AND THE WIRING
Illustration 2 g01186024
Location of the J1/P1 ECM connectors (typical left side engine view)
Thoroughly inspect the J1/P1 ECM connector, the firewall bulkhead connector and the accelerator pedal position sensor connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01255058
Terminal locations at the P1 ECM connector for the accelerator pedal position sensor
(P1-4) Sensor supply (8 VDC)
(P1-5) Sensor return
(P1-66) Accelerator pedal position sensor
Illustration 4 g01159881
Sensor connector
(Terminal A) Sensor supply
(Terminal B) Sensor return
(Terminal C) Sensor signal
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the accelerator pedal position sensor.
Check the allen head screw for each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and pinch points from the accelerator pedal position sensor to the ECM. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of cor


Parts collar Mariner:

80247M
 
80247M COLLAR, DRIVESHAFT
7015207, 7025207NW, 7025207PW
81873M
 
81873M COLLAR, THRUST & PIVOT SHAFT
7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
81961M
 
81961M COLLAR, THRUST-PIVOT SHAFT
7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
82929M
 
82929M COLLAR
7020201, 7025200, 7025207NW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
95199M
 
95199M COLLAR
7030301
95200M
 
95200M COLLAR
7030301
97596M
 
97596M COLLAR
7025207PW
97600M
 
97600M COLLAR
7025207PW
Back to top