11149A43 Mariner CABLE ASSEMBLY, Brown/White


11149A43 CABLE ASSEMBLY, Brown/White Mariner 7F10203HD, 7F13203UB, 7F15201GD CABLE
11149A43 CABLE ASSEMBLY, Brown/White Mariner
Rating:
93

Buy CABLE ASSEMBLY, Brown/White 11149A43 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Compatible models:

Mariner entire parts catalog list:

7F10203HD 1999,2000,2001,2002,2003,2004,2005
7F13203UB 2006
7F15201GD 1998

Information:


Illustration 1 g01390328
Schematic for the CAN data link for the J1 ECM connector
Illustration 2 g01390398
Schematic for the CAN data link for the J2 ECM connectorTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 3 g01380568
Connector locations for the CAN data link (rear engine view) (1) P1 ECM connector (2) Customer Connector
Illustration 4 g01380580
Connector locations for the CAN data link (top rear engine view) (2) Customer Connector (3) Termination resistor (4) Service tool connector
Thoroughly inspect connectors (1), (2), and (3). Inspect all of the connectors that are associated with the CAN data link. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 5 g01209797
Terminal locations at the P1 ECM connector that are associated with the CAN data link (P1-34) CAN data link − (P1-42) CAN shield (P1-50) CAN data link +
Illustration 6 g01360095
Terminal locations at the Customer Connector that are associated with the CAN data link (P1-16) CAN shield (P1-17) CAN data link + (P1-18) CAN data link −
Illustration 7 g01209794
Terminal locations at the service tool connector that are associated with the CAN data link (Terminal C) CAN shield (Terminal G) CAN data link + (Terminal F) CAN data link −
Illustration 8 g01355248
Terminal locations at the connector for the termination resistor that are associated with the CAN data link (Terminal A) CAN data link + (Terminal B) CAN data link − (Terminal C) CAN shield
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
Check the allen head screw on each ECM connector and on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the wiring harnesses for abrasion, for corrosion and for pinch points.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Verify the Proper Installation of the Termination Resistors
Remove the electrical power from the ECM.
Disconnect the display panel from the data link.
Disconnect the Caterpillar Electronic Technician (ET) from the service tool connector.
Disconnect the P1 ECM connector.Note: Wiggle the harness during the following measurements in order to reveal an intermittent condition.
Measure the resistance between terminals P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -).Expected Result:The resistance is between 57 and 63 Ohms.Results:
OK - The resistance is between 57 and 63 Ohms. Proceed to Test Step 3.
Not OK - The resistance is between 114 Ohms and 126 Ohms. A termination resistor is missing.Repair: Verify that two termination resistors are connected to the data link. One resistor must be located on each end of the data link. The engine is shipped with one termination resistor that is installed between the ECM and the customer connector.Refer to the appropriate electrical schematic in order to determine the missing resistor. Replace the missing resistor. Verify that the problem is resolved.STOP
Not OK - The resistance is less than 57 Ohms. There may be a short circuit in the harness. Proceed to Test Step 3.
Not OK - The resistance is greater than 126 Ohms. There may be an open circuit in the harness. Proceed to Test Step 4.Test Step 3. Check the Harness for a Short Circuit
Remove both termination resistors from the CAN data link.
Disconnect the display panel.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.


Parts cable Mariner:

816311
CABLE TIE, (8.00 Inches)
816311 CABLE TIE, (8.00 Inches)
7002201DK, 7006201CD, 7008218EW, 7008237, 7010312DT, 7015203KL, 70152374D, 7016207CD, 7020201NC, 7030201KL, 7031203GD, 7031207CD, 7031207LF, 7040203KL, 70404119D, 70432037D, 7050302ED, 7050412YD, 7055207GD, 7060412ET, 7075217CD, 7075312SD, 7100412CD,
11149A 3
 
11149A 3 CABLE ASSEMBLY (3")
7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075D73ZY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412U
43242 9
 
43242 9 CABLE, Throttle
7006201CD, 7008218EW, 7010312DT, 7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD
824372A 1
 
824372A 1 CABLE ASSEMBLY
7225412CD, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD
824912A 6
 
824912A 6 CABLE (MANUAL)
7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD
95084A21
 
95084A21 CABLE-FUSE
7F08261DF, 7F10203HD, 7F15201GD
95084A19
 
95084A19 CABLE-FUSE
7F08261DF, 7F10203HD, 7F15201GD
853344 1
 
853344 1 CABLE
7F15201GD
Back to top