93388A14 Mariner CABLE ASSEMBLY, Yellow/Black


93388A14 CABLE ASSEMBLY, Yellow/Black Mariner 7115473JD, 7135412JD, 7135473HD, 7150413LD, 7150423JD, 7200413JD, 7200473HD, 7200473JD, 7225413LD CABLE
93388A14 CABLE ASSEMBLY, Yellow/Black Mariner
Rating:
43

Buy CABLE ASSEMBLY, Yellow/Black 93388A14 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

Mariner entire parts catalog list:

7115473JD 2000
7135412JD 2000,2001,2002,2003,2004,2005
7135473HD 1999
7150413LD 2002,2003
7150423JD 2000,2001
7200413JD 2000
7200473HD 1999
7200473JD 2000
7225413LD 2002,2003

Information:


Table 1
Diagnostic Trouble Codes    
J1939 Code     CDL Code     Code Description
(code descriptions may vary)     Comments    
190-8     190-8     Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period     The code is logged. The Electronic Control Module (ECM) can default to the secondary engine speed/timing sensor. The default will occur if a valid signal is not received from the primary engine speed/timing sensor. The engine will shut down only if the signals from the primary engine speed/timing sensor and the secondary engine speed/timing sensor are abnormal.    
723-8     342-8     Secondary Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period     The code is logged. If a valid signal is not received from the secondary engine speed/timing sensor, the ECM will default to the primary engine speed/timing sensor. The engine will shut down only if the signals from the primary engine speed/timing sensor and the secondary engine speed/timing sensor are abnormal.    The engine uses two engine speed/timing sensors. Both sensors detect the reference for engine speed and timing. The ECM uses the pulses in order to determine the position of the crankshaft. The ECM measures the time between the pulses that are created by the sensors as the gears rotate in order to determine rpm.After locating the No. 1 cylinder, the ECM triggers each injector in the correct firing order and at the correct unit injector timing. The actual timing and duration of each injection is based on engine rpm and load. If the engine is running and the signal from the primary engine speed/timing sensor is lost, a slight change in engine performance will be noticed. The change will be noticed when the ECM performs the changeover to the secondary engine speed/timing sensor. Loss of the signal from the secondary engine speed/timing sensor during engine operation will not result in any noticeable change in engine performance. However, if the signal from the secondary engine speed/timing sensor is not present during start-up the following conditions may exist:
The engine may require a slightly longer amount of time to start up.
The engine may run rough for a few seconds until the ECM determines the proper firing order by using the primary engine speed/timing sensor only.The engine will start and the engine will run when only one sensor signal is present from either of the sensors. Loosing the signal from both of the sensors during engine operation will result in the termination of injection. The ECM will then shut down the engine. The loss of the signal from both of the sensors during start-up will prevent the engine from starting.Both sensors are magnetic sensors with an integral connector. The two sensors are not interchangeable. Do not switch the positions of the sensor. If the sensors are replaced, a timing calibration is not necessary for the engine.
Illustration 1 g02947337
Table 2
Troubleshooting Test Steps    Values    Results    
1. Check the Engine Speed/Timing Circuit
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Turn the keyswitch to the ON position.
C. Monitor the "Engine Starting" screen in Cat ET.
Start the engine and run the engine. The problem may occur when the engine is at any operating temperature. However, the problem is more likely to occur when the engine is at the normal operating temperature.
   
Engine starting    
Result: The engine started.
Proceed to Test Step 2.
Result: The engine did not start.
Proceed to Test Step 3.
   
2. Check for Diagnostic Codes
A. While the engine is running monitor Cat ET for diagnostic codes. Also monitor the "Engine Starting" screen for an engine speed/timing that is "Not Detected".
B. Wait at least 30 seconds for activation of the diagnostic codes. Look for these codes on Cat ET:
190-8
342-8
723-8
   
Diagnostic Trouble Codes    
Result: There is an active diagnostic code or there is a timing pattern that is "Not Detected".
Proceed to Test Step 5.
Result: There is not an active diagnostic code and there is not a timing pattern that is "Not Detected".
Download the "Warranty Report" from the engine ECM. Troubleshoot any diagnostic codes that may be present.
Return the unit to service.
   
3. Check the Battery Voltage
A. Monitor the "Engine Starting" screen in Cat ET.
Monitor the battery voltage. Crank the engine for five seconds.
Monitor the battery voltage while cranking.    
Battery voltage    
Result: The battery voltage is OK.
Proceed to Test Step 4.
Result: The battery voltage is not OK.
Refer to Troubleshooting, "Engine Cranks but Does Not Start".
   
4. Check the Engine Speed and the Engine Speed/Timing Status
A. Monitor the "Engine Starting" screen in Cat ET.
B. Crank the engine for five seconds. While the engine is cranking, verify that the sensors show an acceptable cranking speed.
C. While the engine is cranking check the status of the engine speed/timing sensors.
   
Crank speed    
Result: The sensors show an acceptable cranking speed. The timing pattern shows "Detected".
Refer to Troubleshooting, "Engine Cranks but Does Not Start".
Result: A sensor does not show an acceptable cranking speed and/or the timing pattern shows "Not Detected".
Proceed to Test Step 5.
   
Illustration 2 g02227733
Typical left side engine view (1) Crankshaft speed/timing sensor
Illustration 3 g02227753
(2) Camshaft speed/timing sensor
Table 3
Troubleshooting Test Steps    Values    Results    
5. Inspect the Sensor Assembly
A. Turn the keyswitch to the OFF position.
B. Visually inspect the sensor and the sensor assembly without removing the sensor assembly from the engine. Flanges must be flush against the surface of the front timing gear housing in order to ensure proper operation.
C. Inspect the sensor bracket . Verify that the bracket securely holds the flanges of the sensors flush against the engine.
Verify that the bracket is not bent. If the bracket is bent or if an obstruction is preventing the sensor assembly from being installed correctly, the engine will not start.
Disconnect the harness from the speed/timing sensors. Check the harness for debris and for corrosion.
Perform a 45 N (10 lb) pull test on the harness wiring.
   
Debris and/or corrosion
Mounting bracket    


Parts cable Mariner:

816311
CABLE TIE, (8.00 Inches)
816311 CABLE TIE, (8.00 Inches)
7002201DK, 7006201CD, 7008218EW, 7008237, 7010312DT, 7015203KL, 70152374D, 7016207CD, 7020201NC, 7030201KL, 7031203GD, 7031207CD, 7031207LF, 7040203KL, 70404119D, 70432037D, 7050302ED, 7050412YD, 7055207GD, 7060412ET, 7075217CD, 7075312SD, 7100412CD,
88807A16
 
88807A16 CABLE ASSEMBLY, (4.00 Inches-Black)
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 7031203GD, 7031207CD, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050717, 7055207GD,
88807A20
 
88807A20 CABLE ASSEMBLY, COVER
7031203GD, 7031207CD, 7150413ED, 7150413HD, 7150423JD, 7175413AD, 7175413PD, 7175413YD, 7175423HD, 7200413JD, 7220727
88807A19
 
88807A19 CABLE ASSEMBLY
7150413ED, 7150413HD, 7150423JD, 7175413AD, 7175413PD, 7175413YD, 7175423HD, 7200413JD, 7220727
88439A24
 
88439A24 CABLE ASSEMBLY, Negative - Battery
7135412ED, 7135412HD, 7135412JD, 7150413ED, 7150413HD, 7150423JD, 7175423HD, 7200413JD, 7225412CD, 7225412HD, 7225413DD, 7225413HD
88807A27
 
88807A27 CABLE ASSEMBLY
7115473JD, 7135473GD, 7135473HD, 7200473GD, 7200473HD, 7200473JD, 7200473KD
821945T65
CABLE ASSEMBLY, Hi Tension
821945T65 CABLE ASSEMBLY, Hi Tension
7115473JD, 7135473HD, 7200473JD
858702T 1
 
858702T 1 CABLE ASSEMBLY, Adaptor
7150423JD, 7200413JD
Back to top