41482A 2 Mariner CHECK VALVE KIT


41482A 2 CHECK VALVE KIT Mariner 7075312ND, 7075312SD, 7075524, 7075717, 7090524, 7100412NC, 7115520, 71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727 CHECK
41482A 2 CHECK VALVE KIT Mariner
Rating:
103

Buy CHECK VALVE KIT 41482A 2 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Mariner entire parts catalog list:

7075312ND 1988,1989
7075312SD 1990,1991,1992,1993
7075524 1984,1985,1986
7075717 1987,1989
7090524 1984,1985,1986,1987,1988
7100412NC 1988,1989,1990,1991,1992,1993
7115520 1980
71354120D 1990,1991
7135417PD 1989
7135826 1986,1987,1988
7150453ND 1988
7150453PD 1989,1990
7150629 1979,1980,1982,1984,1985
7175412PD 1989
7175413PD 1989,1990
7175413YD 1991
7175629 1979,1980,1985,1986,1988
7200412PD 1989,1990
7200620 1980,1982,1983,1984,1985,1986,1988
7220727 1987,1988

Information:

Probable Causes
Diagnostic codes
ECM parameters
Throttle position sensor
Air intake and exhaust system
Fuel supply
Individual malfunctioning cylinders
Fuel injection nozzlesRecommended Actions
Diagnostic Codes
Check for active diagnostic codes on the electronic service tool. Troubleshoot any active codes before continuing with this procedure.ECM Parameters
Ensure that the fault is not a programmed parameter.
Ensure that the correct mode was selected by using the electronic service tool.
Use the electronic service tool to verify the correct engine rating for the engine.
Use the electronic service tool to verify the maximum engine speed limit.
Use the electronic service tool to reset the parameters to the OEM specifications.
Ensure that the repairs have eliminated the faults.
If the repairs have not eliminated the faults proceed to "Throttle Position Sensor". Throttle Position Sensor
Use the electronic service tool and observe the signal for the throttle position sensor.
If the signal is erratic, refer to Troubleshooting, "Throttle Position Sensor Circuit - Test".
If the engine has a throttle switch refer to Troubleshooting, "Throttle Switch Circuit - Test".
If the repairs have not eliminated the faults proceed to "Air Intake and Exhaust System". Air Intake and Exhaust System
Check the air filter restriction indicator, if equipped.
Ensure that the air filter is clean and serviceable.
Check the air intake and the exhaust system for the following defects:
Blockages
Restrictions
Damage to the air intake and exhaust lines and hoses
Make all necessary repairs to the engine.
Ensure that the repairs have eliminated the diagnostic code.
If the fault has not been eliminated, proceed to "Fuel Supply". Fuel Supply
Check the fuel pressure. Refer to Systems Operation, Testing and Adjusting, "Fuel System Pressure - Test".
Ensure that the fuel system has been primed. Refer to Systems Operation, Testing and Adjusting, "Fuel System - Prime".
Check the diesel fuel for contamination. Refer to Systems Operation, Testing and Adjusting, "Fuel Quality - Test".
Check for air in the fuel system. Refer to Systems Operation, Testing and Adjusting, "Air in Fuel - Test".
Check that the fuel lines are tight and secured properly.
Check for fuel supply lines that are restricted.
Check the fuel filters.
Visually check the fuel tank for fuel. The fuel gauge may be faulty.
If the engine has a water separator, check for water in the fuel.
Ensure that the fuel supply valve is in the full OPEN position.
If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
If the repairs do not eliminate the fault proceed to "Individual Malfunctioning Cylinders". Individual Malfunctioning Cylinders
With the engine speed at a fast idle, loosen the high pressure fuel line to the fuel injection nozzle of number 1 cylinder. Note if there is any reduction in engine speed. Tighten the high pressure fuel line to the fuel injection nozzle.
If all cylinders have been checked and no faults were detected proceed to "Fuel Injection Nozzles". Fuel Injection Nozzles
Remove the fuel injection nozzles from the cylinder head. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Remove".
Check the fuel injection nozzles. Refer to Testing and Adjusting, "Fuel Injection Nozzle - Test".
Install the fuel injection nozzles in the cylinder head. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
Ensure that the repairs have eliminated the fault.


Parts check Mariner:

77560
 
77560 CHECK VALVE, BLEED HOSE - TOP
7080508, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
77561
 
77561 CHECK VALVE, BLEED HOSE - BOTTOM
7070509, 7070520, 7080508, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
30430A10
 
30430A10 CHECK VALVE ASSEMBLY
7090520, 7090529, 7115520, 7115529, 7140629
42657A 1
 
42657A 1 CHECK VALVE
7008237, 7050412YD, 7060412ET, 7075312ND, 7075312SD, 7075717, 7100412NC, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200620, 7250422PD
30430A 8
 
30430A 8 CHECK VALVE ASSEMBLY
7135826, 7150629, 7175629, 7200620
30430A11
30430A12
42481
 
42481 CHECK VALVE (NOT USED W/SQUARE FUEL PUMP)
7075312ND, 7075312SD, 7075717, 7100412NC, 7175413AD, 7175413PD, 7175413YD, 7200620, 7220727
Back to top