8665 Mariner CHOKE SHUTTER (MANUAL)


8665 CHOKE SHUTTER (MANUAL) Mariner 7045217, 7050200, 7050716 CHOKE
8665 CHOKE SHUTTER (MANUAL) Mariner
Rating:
43

Buy CHOKE SHUTTER (MANUAL) 8665 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

Mariner entire parts catalog list:

7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050716 1986

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01344541
Typical example
Place a suitable container below the engine oil pan. Remove drain plug (5) and drain the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Illustration 2 g01251767
Typical example
Remove O-ring seal (11) from drain plug (5).
Disconnect breather hose (1) from clip (6). Position the breather hose away from the engine oil pan.
If necessary, remove the assembly of dipstick tube. Loosen nut (3) and remove tube assembly (2). Remove seal (4) from the tube assembly. Note: Identify the position and orientation of the tube assembly.
Support the assembly of the engine oil pan. Mark the position of clip (6). Loosen the bolt that secures the clip and remove the clip.
Remove bolts (9) and (10).
Remove engine oil pan (8) and remove joint (7) from the cylinder block. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
(M8 by 100 mm) 4
B - Loctite 5900 -
C - Loctite 5188 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the mating surface of the cylinder block is clean and free from damage.
Illustration 3 g01251768
Typical example
Install Tooling (A) to positions (X) in the cylinder block.
Ensure that the engine oil pan is clean and free from damage.
Illustration 4 g01251763
Typical example
Illustration 5 g01251766
Typical example
Apply a bead of Tooling (B) to positions (Y) on the cylinder block. Note: If the bridge piece for the cylinder block has just been installed, the engine oil pan must be installed before Tooling (B) has cured.
Illustration 6 g01251767
Typical example
Position a new joint (7) onto engine oil pan (8).
Illustration 7 g01344541
Typical example
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the cylinder block.
Install bolts (9) finger tight. Install clip (6) in the correct position.
Remove Tooling (A).
Apply Tooling (C) to bolts (10). Install bolts (10) and remaining bolts (9).
Tighten bolts (9) and (10) to a torque of 22 N m (16 lb ft).
Install a new O-ring seal (11) to drain plug (5). Install the drain plug to engine oil pan (8). Tighten the oil drain plug to a torque of 34 N m (25 lb ft).
If necessary, follow Steps 12.a through 12.c in order to install the assembly of the dipstick tube.
Install a new seal (4) to tube assembly (2).
Apply Tooling (C) to nut (3). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten nut (3) to a torque of 18 N m (13 lb ft). Install the dipstick.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the procedure.


Parts choke Mariner:

76076A 1
 
76076A 1 CHOKE ROD
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
90242A 1
 
90242A 1 CHOKE KNOB ASSEMBLY
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070520, 7075524, 7080629, 7090520
96773A 1
 
96773A 1 CHOKE SHAFT
7045217, 7050200, 7050716
5197
54293A11
 
54293A11 CHOKE SOLENOID - ELECTRIC
7045217, 7050200, 7050716
85966A 1
 
85966A 1 CHOKE ROD ASSEMBLY
7045217, 7050200, 7050716
60549A 7
 
60549A 7 CHOKE SOLENOID
7050716, 7050717, 7060312PC, 7060524
Back to top