80752M Mariner CLAMP


80752M CLAMP Mariner 7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 704 CLAMP
80752M CLAMP Mariner
Rating:
48

Buy CLAMP 80752M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Mariner entire parts catalog list:

7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7005227 1977
7008204 1984,1985,1986
7008208 1978
7008226 1986
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7010209 1979,1983,1984,1985,1986
7015207 1977
7015307 1977
7015327 1987
7015529 1979
7020201 1981
7025200 1980
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7040202 1982,1985,1986
7040207 1977
7040207PW 1989,1990,1991,1992,1993
7040208 1978
7040328 1978,1980
7040507 1987
7040716 1986
7048207 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978

Information:


Table 1
Tools Needed Quantity
4C-6594 Timing and Fuel Setting Tool 1
6V-3075 Dial Indicator 1
5P-4814 Collet Clamp 1
5P-7263 Indicator Contact Point 1 Fuel setting is the adjustment of the fuel setting screw to a specified position. The fuel setting screw limits the power output of the engine by setting the maximum travel of all the fuel injector racks.
Illustration 1 g00559781
4C-6594 Timing and Fuel Setting Tool
(1) 5P-4814 Collet Clamp. (2) 6V-3075 Dial Indicator. (3) 5P-7263 Indicator Contact Point.
Before the fuel setting is checked, the fuel injectors must be correctly synchronized. See the subject Fuel Injector Synchronization.
Illustration 2 g00559811
Fuel Injection Linkage Control Housing
(4) Synchronizing pin. (5) Fuel setting screw. (6) Fuel setting cover. (Y) Location for the dial indicator. (Z) Location for the synchronizing pin.
Remove the plugs from the housing assembly at location (Y) and (Z).
Remove synchronizing pin (4), and install the pin in the threaded hole at location (Z) without the washer. Tighten the synchronizing pin.
Illustration 3 g00559957
Installation Of The Synchronizing Pin
(4) Synchronizing pin. (5) Fuel setting screw. (6) Fuel setting cover. (7) Fuel stop lever. (Y) Location for the dial indicator.
Move the actuator terminal shaft lever in the "FUEL ON" direction until the flat face of fuel stop lever (7) contacts synchronizing pin (4).
Illustration 4 g00560054
Installation Of 6V-3075 Dial Indicator
(2) 6V-3075 Dial Indicator. (4) Synchronizing pin.
Put 6V-3075 Dial Indicator (2) with 5P-7263 Contact Point (3) in 5P-4814 Collet clamp (1).
Install the dial indicator (2) and the collet in the threaded hole at location (Y). When the contact point seats against fuel stop lever (7), slide the dial indicator inward or slide the dial indicator outward until the dial indicator gives a reading of 0.00 mm (0.000 inch). Tighten the collet enough in order to hold the dial indicator in position.
Remove synchronizing pin (4). Slowly move the actuator terminal shaft in the "FUEL ON" direction until the flat face of fuel stop lever (7) is against the end of the fuel setting screw (5). When the linkage is held in this position, the dial indicator reading will be the present fuel setting.
Illustration 5 g00341652
Engine Information Plate
Note: See the information plate on the engine for the correct full load static fuel setting.
If the fuel setting is correct, remove the dial indicator. Return the synchronizing pin and the washer to the original locations.
Install the plugs at location (Y) and (Z).
If the fuel setting needs adjustment, go on to "Fuel Setting Adjustment". Fuel Setting Adjustment
A mechanic with governor and fuel setting training is the ONLY one to make adjustments to the engine fuel setting.
Note: Before the fuel setting adjustment is made, check the fuel setting. Refer to "Fuel Setting Check".Refer to illustrations 2 through 4.
Cut the seal wire and remove fuel setting cover (6) and the gasket. Loosen the locknut. While "Surface A" of fuel stop lever (7) is held against the end of fuel setting screw (5) turn the fuel setting screw inward or turn the fuel setting screw outward. Turn the fuel setting screw inward or turn the fuel setting screw outward until the correct reading is shown on the dial indicator.
Tighten the locknut on fuel setting screw (5). Be sure that the fuel setting screw does not turn when the locknut is tightened.
Release the fuel control linkage. Again, move the linkage all the way in the "FUEL ON" direction. Check the dial indicator reading again in order to ensure that the fuel setting is still correct.
Remove the dial indicator and synchronizing pin (4).
Put fuel setting cover (6) and the gasket in position over the fuel setting screw. Install the bolt and synchronizing pin (4) in the cover. Install a new seal wire.


Parts clamp Mariner:

91698M
 
91698M CLAMP
7004201, 7005201, 7005207
80093M
 
80093M CLAMP
7003207, 7005207, 7005227
6755M
 
6755M CLAMP BRACKET, STARBOARD
7015207, 7015307, 7015327
80890M
 
80890M CLAMP, COWL
7015207, 7015307, 7015327
82039M
 
82039M CLAMP
7028207, 7028527, 7040207, 7040208, 7040507
82038M
 
82038M CLAMP, HIGH TENSION LEADS
7008208, 7008238, 7008248, 7008305, 7010209, 7015529, 7028207, 7028527
92664M
 
92664M CLAMP
7048227, 7048321, 7055324, 7055524, 7060507
83992M
 
83992M CLAMP (SEE NOTE #2)
7010209, 7015529
Back to top