814589M Mariner CLAMP - ELECTRIC


814589M CLAMP - ELECTRIC Mariner 7030320, 7040706, 7040716 CLAMP
814589M CLAMP - ELECTRIC Mariner
Rating:
63

Buy CLAMP - ELECTRIC 814589M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Compatible models:

Mariner entire parts catalog list:

7030320 1980,1990,1992
7040706 1986,1990,1992
7040716 1986

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Drain the secondary filters. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 1 g03389540
Typical example
Make temporary identification marks on all the plastic tube assemblies to show the correct position of the tube assemblies.
Place a suitable container below the fuel filter base to catch any fuel that might be spilled.
Disconnect plastic tube assembly (1), plastic tube assembly (2), and plastic tube assembly (3) from the fuel filter base.
Use Tooling (A) to plug the plastic tube assemblies. Use Tooling (A) to cap the ports in the fuel filter base.
Illustration 2 g03389546
Typical example
Remove secondary filters (6) from canisters (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Remove bolts (4) from fuel filter base (5). Remove the fuel filter base from the mounting bracket.Note: Do not disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 3 g03389546
Typical example
Ensure that fuel filter base (5) is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Position fuel filter base (5) on the mounting bracket. Install bolts (4). Tighten the bolts to a torque of 44 N m (32 lb ft).
If necessary, install new fuel filters (6) to canisters (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 4 g03389540
Typical example
Remove the plugs from the plastic tube assemblies. Remove the caps from the ports in the fuel filter base.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies to the correct ports will allow contamination to enter the fuel system. Serious damage to the engine will result if contaminated fuel enters the fuel system.
Connect plastic tube assembly (1), plastic tube assembly (2), and plastic tube assembly (3) to fuel filter base (5).
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.


Parts clamp Mariner:

80752M
 
80752M CLAMP
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 704
82042M
 
82042M CLAMP
7015207, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040716, 7060507, 7060528
81145M
 
81145M CLAMP, COWL
7028207, 7028527, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716
84914M
 
84914M CLAMP
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040206, 7040706, 7040716
83577M
 
83577M CLAMP
7002200, 7030320, 7040207, 7040208, 7040507, 7055324, 7115F13KD, 7115F13RD, 7115F13UF, 7F10203HD, 7F13203UB, 7F15201GD, 7F75411JD, 7F75412RD, 7F75413TD
9797M
 
9797M CLAMP BRACKET, PORT
7025207PW, 7025208CW, 7025500, 7026226, 7030205, 7030301, 7030320
9798M
 
9798M CLAMP BRACKET, STARBOARD
7025207PW, 7025208CW, 7025500, 7026226, 7030205, 7030301, 7030320
96654M
 
96654M CLAMP
7030301, 7030320
Back to top