82612M Mariner CLAMP, COWL...


82612M CLAMP, COWL... Mariner 7008238, 7008247 CLAMP
82612M CLAMP, COWL... Mariner
Rating:
98

Buy CLAMP, COWL... 82612M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 30
 

Compatible models:

7008238   7008247   Mariner

Mariner entire parts catalog list:

7008238 1978
7008247 1977,1987

Information:

Type 1 Fuel Filters
Illustration 1 g02791865
Typical example
Loosen the vent screw (1) on the secondary fuel filter base.
Operate the priming lever of the fuel priming pump to eliminate any air between the fuel priming pump and the fuel filters.Note: The fuel priming pump is mechanically operated by the camshaft. If the lobe of the camshaft is acting upon the arm of the fuel priming pump, the ability to hand prime the fuel system will be reduced. If the resistance on the priming lever is low, rotate the crankshaft in order to move the camshaft lobe off the fuel priming pump arm.
Operate priming lever of the fuel priming pump by hand. Check that there is correct resistance on the fuel priming pump. Operate the fuel priming pump until fuel, free of air, comes from the vent screw.
Tighten the vent screw (1) to a torque of 20 N m (15 lb ft)
Energize the stop solenoid on the fuel injection pump. Operate the priming lever of the fuel priming pump several times.
Crank the engine with the throttle lever in the CLOSED position until the engine starts.
Start the engine and run the engine at idle for 1 minute.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Cycle the throttle lever from the low idle position to the high idle position three times. The cycle time for the throttle lever is one second to 6 seconds for one complete cycle.Note: To purge air from the fuel injection pump on engines with a fixed throttle, the engine should be run at full load for 30 seconds. The load should then be decreased until the engine is at high idle. This should be repeated three times. This will assist in removing trapped air from the fuel injection pump.
Check for leaks in the fuel system.Type 2 Fuel Filters
Illustration 2 g03651564
Typical example
Loosen the vent plug (1) on the primary fuel filter base.
Operate the priming lever of the fuel priming pump to eliminate any air between the fuel priming pump and the fuel filters.Note: The fuel priming pump is mechanically operated by the camshaft. If the lobe of the camshaft is acting upon the arm of the fuel priming pump, the ability to hand prime the fuel system will be reduced. If the resistance on the priming lever is low, rotate the crankshaft in order to move the camshaft lobe off the fuel priming pump arm.
Operate priming lever of the fuel priming pump by hand. Check that there is correct resistance on the fuel priming pump. Operate the fuel priming pump until fuel, free of air, comes from the vent screw.
Tighten the vent plug (1) .
Energize the stop solenoid on the fuel injection pump. Operate the priming lever of the fuel priming pump several times.
Crank the engine with the throttle lever in the CLOSED position until the engine starts.
Start the engine and run the engine at idle for 1 minute.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Cycle the throttle lever from the low idle position to the high idle position three times. The cycle time for the throttle lever is one second to 6 seconds for one complete cycle.Note: To purge air from the fuel injection pump on engines with a fixed throttle, the engine should be run at full load for 30 seconds. The load should then be decreased until the engine is at high idle. This should be repeated three times. This will assist in removing trapped air from the fuel injection pump.
Check for leaks in the fuel system.


Parts clamp Mariner:

82047M
 
82047M CLAMP
7002207, 7003207, 7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008218EW, 7008226, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226,
82046M
 
82046M CLAMP
7002200, 7002207, 7003207, 7004201, 7005201, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7
6703M
 
6703M CLAMP BRACKET
7003207, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
80752M
 
80752M CLAMP
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 704
80511M
 
80511M CLAMP, FRICTION...
7008238, 7008247
81709M
 
81709M CLAMP BRACKET...
7008208, 7008238, 7008247, 7008248
81064M
 
81064M CLAMP, COWL...
7008238, 7008247
82033M
 
82033M CLAMP, CORD...
7008238, 7008247, 7028207, 7028527, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060528
Back to top