82343M Mariner CLIP, PISTON PIN


82343M CLIP, PISTON PIN Mariner 7010209, 7015207, 7015529, 7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD CLIP
82343M CLIP, PISTON PIN Mariner
Rating:
48

Buy CLIP, PISTON PIN 82343M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015207 1977
7015529 1979
7F08203HF 1999
7F08261DF 1995,1996,1997,1998
7F10203HD 1999,2000,2001,2002,2003,2004,2005
7F13203UB 2006
7F15201GD 1998

Information:


Illustration 1 g01167557
Schematic diagram for the electrical power supply
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 2 g01167488
Engine view (typical example)
(1) J1/P1 ECM connectors
Illustration 3 g01146383
Left side view
(2) P61 customer connector
Thoroughly inspect connectors (1) and (2). Inspect the connections for the battery and the connections to the keyswitch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 4 g01104383
P1 terminals that are associated with the electrical power supply
(P1-44) Shutdown switch
(P1-48) +Battery
(P1-52) +Battery
(P1-53) +Battery
(P1-61) −Battery
(P1-63) −Battery
(P1-65) −Battery
(P1-70) Keyswitch
Illustration 5 g01167609
J61 and P61 terminals that are associated with the electrical power supply
(1) +Battery
(26) Keyswitch
(27) Shutdown
(31) +Battery
(32) +Battery
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the electrical power supply.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM. Also, check the harness and wiring for abrasions and for pinch points from the keyswitch to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check the Battery Voltage at the ECM
Disconnect the J1/P1 ECM connector.
Measure the voltage between P1-52 (+Battery) and P1-63 (−Battery).
Measure the voltage between P1-48 (+Battery) and P1-61 (−Battery).
Measure the voltage between P1-53 (+Battery) and P1-65 (−Battery).
Turn the keyswitch to the ON position.
Measure the voltage between P1-70 (Keyswitch) and P1-63 (−Battery). Expected Result:The measured voltage is between 11.0 VDC and 13.5 VDC for a 12 volt system and between 22.0 VDC and 27.0 VDC for a 24 volt system with no suspected intermittent problems at this time.Results:
OK - The ECM is receiving the correct voltage. Repair: If an intermittent condition is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - Battery voltage is out of range - Proceed to Test Step 3.
Not OK - Keyswitch voltage out of range - Repair: Trace the wiring for the keyswitch from the ECM through the keyswitch circuit to the batteries. Find the problem and repair the problem. Check the circuit protection for the circuit and for the wiring.Verify that the repairs eliminate the problem.STOPTest Step 3. Check the Condition of the Batteries
Measure the no-load battery voltage at the battery posts.
Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure". Expected Result:The batteries pass the load test. The measured voltage is the minimum specification for a 12V or 24V system.Results:
OK - The batteries are OK.Repair: Check the wiring between the batteries and the ECM for an open circuit or a short circuit.Check the connectors between the batteries and the ECM for moisture and/or corrosion.Repair the wiring and/or the connectors.Verify that the repair eliminates the problem.STOP
Not OK - The battery voltage is low or the battery did not pass the load test.Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOP


Parts clip Mariner:

82045M
 
82045M CLIP
7003207, 7005207, 7005227, 7008238, 7008247, 7015207
82051M
 
82051M CLIP
7005201, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7025207NW, 7025207PW, 7028207, 7028527, 7040207, 7040208, 7040507
30954
 
30954 CLIP, SAFETY
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB, 7020207, 7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD
824918
 
824918 CLIP
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7015201LD, 70152374D, 7020201HB, 7020201TB, 7F10203HD, 7F13203UB, 7F15201GD, 7F25201GD, 7F41452KD, 7F50352HD, 7F50412DD
827489M
 
827489M CLIP
7F08203HF, 7F08261DF
Back to top