16058T Mariner COIL, Exciter


16058T COIL, Exciter Mariner 7004201HB, 7004201UB COIL
16058T COIL, Exciter Mariner
Rating:
33

Buy COIL, Exciter 16058T Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$35.99
 

15-07-2024

CN: movinglife
Stator coil 16058 16058T Stator coil for Mercury-Mercruiser 4HP 4 Stator coil for Mercury-Mercruiser 5HP 5 Stator coil for Mercury-Mercruiser replace Stator coil
Dobest 【Compatible models】The stator coil is suitable for OEM 16058 16058T for Mercury-Mercruiser 4HP 4 stator coil for Mercury-Mercruiser 5HP 5 stator coil || 【Excellent performance】The stator coil of the generator magneto is made of high-quality materials, which is strong, anti-aging, and wear-resistant, ensuring long-term use, stable performance, and higher driving safety. || 【Easy to use】 Simple operation can be installed successfully. Repairs can be completed in a short time and hardly require any mechanical expertise. The installation is simple and does not require complicated tools. || 【Compatible with original models】Original factory standards, professional manufacturing, high precision and high performance. Generator magneto stator coils can directly replace old or faulty generator magneto stator coils. || 【Buy With Confidence】If you have any questions when comparing our products, please feel free to contact us. We will reply to you as soon as possible and provide you with a satisfactory solution.
$29.99
 

15-07-2024
0.4409[0.20] pounds
US: Topteng
Topteng Exciter Coil Stator Coil for Mercury-Mercruiser 4HP, Mercury-Mercruiser 5HP 16058 16058T
Topteng ★This product is suitable for Mercury-Mercruiser 4HP, Mercury-Mercruiser 5HP 16058 16058T. || ★Please confirm the exact year and exact model of your motorcycle before ordering. || ★Own different test machines to design exact accurate parameter for our products. || ★Direct replacement to your old unit. Plug-and-play, direct fit, easy installation. || ★Highest grade lamination materials. Condition: Aftermarket 100% Brand New. Type: Stator Coil. All products shipped are tested.
$29.99
 

15-07-2024
0.4409[0.20] pounds
US: Areyourshop
Areyourshop Exciter Coil Stator Coil for Mercury-Mercruiser 4HP, Mercury-Mercruiser 5HP 16058 16058T
Areyourshop Please confirm the exact year and exact model of your motorcycle before ordering. || This product is suitable for Mercury-Mercruiser 4HP, Mercury-Mercruiser 5HP 16058 16058T. || Direct replacement to your old unit. Plug-and-play, direct fit, easy installation. || Highest grade lamination materials. Condition: Aftermarket 100% Brand New. Type: Stator Coil. All products shipped are tested. || Own different test machines to design exact accurate parameter for our products.
Number on catalog scheme: 2
 

Compatible models:

Mariner entire parts catalog list:

7004201HB 1999,2000,2001,2002,2003,2004,2005
7004201UB 2006

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) T400011 Crankshaft Turning Tool 1
A(2) 27610291 Housing 1
27610289 Engine Turning Tool 1
B - E12 Torx Socket 1
C 21825607 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g06362599
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod.Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin.Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g06360869
Install connecting rod cap (2) to connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Use Tooling (B) tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) and Tooling (C) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings.Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.
If the glow plugs were removed, install the glow plugs. Ref to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.


Back to top