818141A 2 Mariner CONNECTING ROD KIT


818141A 2 CONNECTING ROD KIT Mariner 7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135473GD, 7135473HD, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7175413AD, 7175413YD, 7175423HD, 7200413JD, 7200413UY, 7200413ZY, 7200423U CONNECTING
818141A 2 CONNECTING ROD KIT Mariner
Rating:
8

Buy CONNECTING ROD KIT 818141A 2 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mariner entire parts catalog list:

7002201DK 1995
7115473JD 2000
71354120D 1990,1991
7135412AD 1992,1993,1994,1995
7135412ED 1996,1997,1998
7135412HD 1999
7135412JD 2000,2001,2002,2003,2004,2005
7135473GD 1998
7135473HD 1999
7150413ED 1996,1997,1998
7150413HD 1999
7150413LD 2002,2003
7150413RD 2004,2005
7150413UY 2006
7150413ZY 2006
7150423JD 2000,2001
7175413AD 1992,1993,1994,1995
7175413YD 1991
7175423HD 1999
7200413JD 2000
7200413UY 2006
7200413ZY 2006
7200423UY 2006

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     153-8487     Stud Tensioner Tool Gp     4    
156-7166 Electric Hydraulic Pump Gp (1)     1    
156-7167 Manual Hydraulic Pump (1)     1    
178-9312 Hose As     4    
178-9313 Coupler Block Gp     1    
B     126-6918     Lifting Bracket     1    
126-6920 Handle Rod     1    
4J-7945 Bolt     2    
C     185-0683     Pressure Gauge As (Comparison)     1    
D     184-3131     Socket As (Cylinder Head Stud)     1    
E     4C-9515     Overhaul Protection Kit (2)     1    
H     4C-5594     Water and Temperature Resistant Grease     -    
J     5P-3931     Anti-Seize Compound     -    
( 1 ) Either pump may be used for this procedure.
( 2 ) The 4C-9515 Overhaul Protection Kit provides all the protective covers and plugs for one cylinder. Use these protective covers in order to maximize the protection during these procedures.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove Tooling (E) from the cylinder block.Note: Protect the stud threads from paint.
Remove all debris from the holes in the cylinder block. Thoroughly clean the studs. If the studs are cleaned to the bare metal, paint the studs.
Thoroughly clean the top of the cylinder block and the sealing surfaces on the cylinder block.
Remove all debris from the inside of the cylinder and the top of the piston. Lubricate the inside of the cylinder liner with clean engine oil.
If the cylinder head studs were removed, use the following Steps to install the studs:
Coat the lower halves of the studs with approximately 1.5 mm (0.06 inch) of Tooling (H) .
Carefully lower the studs into the cylinder block and start the threads by hand.
Tighten the studs to a torque of 100 20 N m (75 15 lb ft).
Coat the entire length of the studs with Tooling (H) .
Always install the seal carriers after the cylinder liners are installed. Aluminum debris that is shaved from the plates by the cylinder liners will prevent the cylinder liners from sealing if the seal carriers are installed first.
Illustration 1 g01213276
Bottom of seal carriers
Illustration 2 g01213278
Top of seal carriers
Illustration 3 g01213037
Install new O-ring seals in the bottom of seal carriers (8) and (11) .
Place seal carriers (8) and (11) over the studs and onto the cylinder block. Install new O-ring seals in the top of the seal carriers.
Place combustion gasket (13) in position on top of cylinder liner (12) and place sleeve (9) in position.
Attach Tooling (B) and a suitable lifting device to the rocker arm support on the cylinder head. The weight of the cylinder head is approximately 205 kg (450 lb).
Illustration 4 g00651274
Typical example
Carefully lift the cylinder head over the studs. Reach through the opening in the side cover in order to hold rod (1) so that the rod does not interfere with the installation of the cylinder head. Slowly lower the cylinder head onto the cylinder block.Make sure that the cylinder head is seated on the dowels and the seal carriers. Make sure that the O-ring seals are properly seated.Show/hide ta


Parts connecting Mariner:

8119A 5
 
8119A 5 CONNECTING ROD ASSEMBLY
71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620
813269
CONNECTING ROD
813269 CONNECTING ROD
7002201DK, 7002201HB, 7002201SK, 7002201UB, 7003201BK
833146A 3
 
833146A 3 CONNECTING ROD ASSEMBLY
7115473JD, 7135473GD, 7135473HD, 7200473GD, 7200473HD, 7200473JD, 7200473KD
822373A 7
 
822373A 7 CONNECTING ROD ASSEMBLY
7200413JD, 7200473KD, 7200D73MD, 7200D73RD, 7225412HD, 7225413HD, 7225413LD, 7225413RD
Back to top