851859 Mariner CONNECTOR


851859 CONNECTOR Mariner 7040203KL, 7040203UL CONNECTOR
851859 CONNECTOR Mariner
Rating:
58

Buy CONNECTOR 851859 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$0.45
 

17-06-2023
0.0006[0.00] Pounds
-: -
Hardware Essentials 851859 Square Bend Hook Zinc 0.192" x 2-5/8" - 3 Pack
Use to hang items and organize || Holds up to 5lbs || Do not use to hang loads, lift loads, support weight of persons or objects || Size: 0.192" x 2-5/8"
$56.17

14-03-2025
2.7[1.22] pounds
US: Auto Parts Direct To
APDTY 851859 Manual Window Regulator (Non-Powered)
APDTY Meets Or Exceeds OEM Specs || Factory OEM Fit Form And Function
Number on catalog scheme: 45
 

Compatible models:

Mariner entire parts catalog list:

7040203KL 2001,2002,2003,2004,2006
7040203UL 2006

Information:


Typical Example2. Remove three bolts (1), washers and nuts. Remove one bolt (2) and washer. Remove guard (3).
Typical Example3. Remove four bolts (4), nut and washers. Remove section (5) from turbocharger (6).4. Fasten a strap and a suitable lifting device to turbocharger (6). Disconnect all engine coolant and engine oil lines from turbocharger (6). After all lines are disconnected remove guard (7) from the turbocharger.5. Loosen clamp (8) that connects turbocharger (6) to the compressor housing.
Typical Example6. Loosen clamp (9) and remove elbow (10) from the turbocharger and muffler.7. Remove four bolts (11) and nuts that holds turbocharger (6) to the exhaust manifold. Remove turbocharger (6). The weight of the turbocharger is 32 kg (70 lb).8. Install the turbochargers in the reverse order of removal.9. Put 5P3931 Anti-Seize Compoundon the threads of bolts (11).10. Tighten bolts (11) to a torque of 55 7 N m (41 5 lb ft).11. Fill the radiator to the correct level with coolant. Refer to the Operation and Maintenance Manual for further information.Disassemble Turbochargers
Start By:a. remove turbochargers 1. Put the turbocharger in position on Tool group (A) as shown.2. Put marks on the housings of the turbocharger for correct installation and alignment at assembly.3. Loosen clamp (2) and remove compressor housing (3) and clamp (2) from the cartridge assembly. 4. Loosen clamp (4) and remove cartridge assembly (5) from turbine housing (6).
To prevent a bent shaft, do not put a side force on the turbine shaft when the compressor wheel nut is loosened.
5. Put the end of the turbine shaft in Tooling (B). Use a universal joint and socket of the correct size to remove the nut that holds compressor wheel (7) on the turbine shaft. 6. Use a press and push the turbine shaft out of compressor wheel (7) and the cartridge housing. Remove compressor wheel (7) from the cartridge housing. 7. Remove shroud (9) from turbine shaft (8). 8. Remove seal ring (10) from turbine shaft (8). 9. Bend the tabs of the locks from bolts (11) and remove the bolts.10. Remove backplate assembly (12) from the cartridge housing. Make a note of the position of the oil holes in the backplate assembly and cartridge housing for correct alignment at assembly. 11. Push spacer (13) out of the bore in backplate (12). 12. Remove seal rings (14) from spacer (13). 13. Remove seal (15) from the cartridge housing. 14. Remove thrust collar (16) from the cartridge housing. 15. Remove thrust bearing (17) from the cartridge housing. If the bearings are to be used again, put identification on them as to their location for correct assembly.16. Remove bearing (18) from the cartridge housing. 17. Remove washer (19) from the cartridge housing. 18. Remove snap rings (20) and (21) with Tooling (C). 19. Remove bearing (22) from the cartridge housing. 20. Remove washer (23) from the cartridge housing. 21. Remove snap ring (24) from the cartridge housing with Tooling (C). 22. Turn the cartridge housing over. Remove plates (25) from the cartridge housing.Assemble Turbochargers
Use the following procedures to assemble the turbocharger. Also refer to Specifications Manual SENR5189 for additional information.1. Check the turbocharger cartridge housing, backplate assembly and bearings to make sure all oil passages are clean and free of dirt and foreign material.2. Put clean engine oil on all parts of the cartridge at assembly. 3. Install plates (1) on the cartridge housing. Turn the cartridge housing over. Make sure the round edge on the outside diameter of the snap ring is toward the bearing when the snap rings are installed.4. Install snap ring (2) in the turbine end of the cartridge housing with Tool (A). Install washer (4) and bearing (3). 5. Install snap ring (5) in the cartridge housing with Tool (A) to hold the washer and bearing in place. 6. Install snap ring (6) in the cartridge housing with Tool (A).7. Install washer (8) and bearing (7) in the cartridge housing until washer (8) makes contact with snap ring (6). 8. Install thrust bearing (9) over the dowels in the cartridge housing. Make sure the grooves in bearing (9) are toward the outside as shown. 9. Put thrust collar (10) in position on the thrust bearing with the counterbore for the spacer up. 10. Install seal ring (11) in the groove of the cartridge housing. 11. Install seal rings (12) on spacer (13) so the gaps in the seal rings are 180 degrees apart. 12. Install spacer (13) in backplate assembly (14). 13. Make sure the oil passage in the cartridge housing and the oil passage in the backplate assembly are in alignment. Put backplate assembly (14) in position on the cartridge housing. Make sure the spacer fits correctly in the counterbore of the thrust collar.14. Install the locks and bolts to hold backplate assembly (14) to the cartridge housing. Tighten the bolts to a torque of 10 1 N m (90 9 lb in)and bend the tabs of the locks on the bolts. 15. Put turbine shaft (15) in position in Tool (B). Put 6V2055 High Vacuum Grease in the groove for seal ring (16). Make sure the grease fills the groove approximately one half or more of the groove depth for the complete circumference of the groove to help make a carbon dam under the seal ring. Install seal ring (16) on turbine shaft (15). 16. Install shroud (17) on turbine shaft (15). 17. Install the cartridge housing on the turbine shaft while the spacer in the backplate is held in position. Make sure the seal ring on the turbine shaft is fitted correctly in the cartridge housing. 18. Put compressor wheel (18) in position on the turbine shaft.
Do not


Parts connector Mariner:

812960
 
812960 CONNECTOR
7002201DK, 7002201HB, 7002201SK, 7002201UB, 7003201BK, 7006201UK, 7015203KL, 7015203UL, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF, 7040203UL
89771 2
 
89771 2 CONNECTOR, (.250-18) (STRAIGHT)
7040203UL, 7150413ED, 7150413HD, 7175423HD, 7200413JD, 7225413DD, 7225413HD
823532A 1
 
823532A 1 CONNECTOR KIT, Fuel
7015203KL, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF, 7040203KL
853736 1
 
853736 1 CONNECTOR, Fuel
7006201MK, 7006201UK, 7015203KL, 7015203UL, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF, 7040203KL, 7040203UL
853736
CONNECTOR, Fuel
853736 CONNECTOR, Fuel
7006201MK, 7006201UK, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF, 7040203KL, 7040203UL
Back to top