99051M Mariner EXTENSION


99051M EXTENSION Mariner 7008204, 7008208, 7008218EW, 7008226, 7008425, 7010209, 7015529, 7020201, 7025200, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040208PW, 7040706, 7040716 EXTENSION
99051M EXTENSION Mariner
Rating:
78

Buy EXTENSION 99051M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008218EW 1996,1998
7008226 1986
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997
7010209 1979,1983,1984,1985,1986
7015529 1979
7020201 1981
7025200 1980
7025207PW 1989,1990,1991,1992,1993
7025500 1980
7026226 1986,1988
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207PW 1989,1990,1991,1992,1993
7040208PW 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998
7040706 1986,1990,1992
7040716 1986

Information:


Illustration 1 g03389877
Typical example
Use a suitable tool in order to remove temperature sensor (6) from the Clean Emissions Module (CEM).
Remove bolt (4) and the washer from the harness assembly clip (5).
Disconnect harness assembly (9) from harness assembly (10).
Cut cable straps (11) from harness assembly (10). Note: Ensure that all cable straps are removed for the harness assembly.
Remove bolts (1) and spacers (2) from bracket (3).
Remove bolts (8) and spacers (7) from bracket (3).
Remove bracket (3) from the CEM bracket.
Remove bolts (13) and spacers (14) (not shown) from bracket (12).
Illustration 2 g03389883
Use a suitable tool in order to remove temperature sensor (17) from the CEM.
Remove bolts (16) and spacers (15) from bracket (12).
Remove bracket (12) from bracket (18) for the CEM.
Illustration 3 g03389963
Make temporary marks on harness assembly (10) for installation purposes.
Make temporary mark on clip (5) for installation purposes. Remove clip (5) from harness assembly (10).
Cut cable straps (19) that secure harness assembly (10) to bracket (12). Note: Ensure that all cable straps are removed for the harness assembly.
Remove harness assembly (10) from bracket (12). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Bostik Pure Nickel
Anti-Seize Compound 1
Ensure that all components of the temperature sensor are clean and free from wear and damage. If any component of the temperature sensor is worn or damaged, the assembly of the temperature sensor must be replaced.
Illustration 4 g03389963
Position harness assembly (10) onto bracket (12). Ensure that harness assembly is correctly orientated onto the bracket.
Install new cable straps (19) that secure harness assembly (10) to bracket (12). Note: Ensure that the cable straps meet the Original Equipment Manufacturer (OEM) specification.
Install clip (5) from harness assembly (10). Ensure that the clip is correctly orientated.
Illustration 5 g03389883
Position bracket (12) onto bracket (18) for the CEM.
Install bolts (16) and spacers (15) from bracket (12) finger tight.
Apply Tooling (A) to the threads of temperature sensor (17).
Use a suitable tool in order to install temperature sensor (17) to the CEM. Tighten the temperature sensor to a torque of 45 N m (33 lb ft). Ensure that the temperature sensor does not come into contact with any part on the CEM.
Illustration 6 g03470560
Illustration 7 g03389877
Install bolts (13) and spacers (14) (not shown) to bracket (12) finger tight.
Tighten bolts (13) and bolts (16) to a torque of 12 N m (106 lb in).
Apply Tooling (A) to the threads of temperature sensor (6). Use a suitable tool in order to install temperature sensor (6) to the CEM.
Install bolt (4) and the washer to the harness assembly clip (5) hand tight. Ensure that the clip is correctly positioned.
Tighten the temperature sensor to a torque of 45 N m (33 lb ft). Ensure that the temperature sensor does not come into contact with any part on the CEM.
Tighten bolts (4) to a torque of 12 N m (106 lb in).
Position bracket (3) onto the CEM bracket.
Install bolts (1) and spacers (2) to bracket (3). Tighten the bolts to a torque of 12 N m (106 lb in).
Position harness assembly (10) onto bracket (3).
Install new cable straps (11) to harness assembly (10). Note: Ensure that cable straps meet the OEM specification.
Connect harness assembly (9) to harness assembly (10).
Turn the battery disconnect switch to the ON position.


Parts extension Mariner:

83194M
 
83194M EXTENSION (LONG SHAFT)...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
83206M
 
83206M EXTENSION, LONG SHAFT
7028207, 7028527
81614M
 
81614M EXTENSION,
7028207, 7028527
83814M
84223M
 
84223M EXTENSION KIT, LONG SHAFT
7008208, 7008238, 7008248, 7008305
84229M
 
84229M EXTENSION KIT, ULTRA LONG SHAFT
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
84230M
 
84230M EXTENSION KIT, SUPER ULTRA LONG SHAFT
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
99060M
 
99060M EXTENSION, LEAD
7008204, 7008208, 7008226, 7010209, 7015529, 7040207PW
Back to top