82132M Mariner COTTER PIN


82132M COTTER PIN Mariner 7004201, 7005201, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7025207NW, 7025207PW, 7025208CW, 7030205, 7030320, 7040206, 7040706, 7040716, 7055324, 7055524 COTTER
82132M COTTER PIN Mariner
Rating:
93

Buy COTTER PIN 82132M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 55
 

Mariner entire parts catalog list:

7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7005227 1977
7008208 1978
7008218EW 1996,1998
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997
7010209 1979,1983,1984,1985,1986
7015207 1977
7015307 1977
7015327 1987
7015529 1979
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025208CW 1994,1995,1996,1997,1998
7030205 1985,1986,1987,1988,1989,1990
7030320 1980,1990,1992
7040206 1986,1987,1988,1989
7040706 1986,1990,1992
7040716 1986
7055324 1984,1985,1988,1989
7055524 1984,1985

Information:


Illustration 1 g00854772
Typical exampleTest Step 1. Check for Connector Damage.
Turn the main disconnect switch to the OFF position.
Turn the circuit breaker CB-8 to the OFF position.
Thoroughly inspect the ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the customer connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).
Check the harness and the wiring for abrasion and pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring should be free of corrosion, abrasion or pinch points.Results:
OK - The connectors and wiring are okay. Proceed to test step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring. Stop.Test Step 2. Check the Status while the "Emergency Kill" Switch is Active.
Start the Caterpillar Electronic Technician (ET).
Turn the main disconnect switch to the ON position.
Turn the circuit breaker CB-8 to the ON position.
Activate the "Emergency Kill" switch. If multiple switches have been installed, ensure that any other "Emergency Kill" switch has not been activated.
Observe the status of the "Emergency Kill" switch on the Cat ET.Expected Result:The parameter for the "Emergency Kill" switch should read "ON".Results:
OK - The "Emergency Kill" switch is working correctly. Proceed to test step 3.
Not OK - The parameter for the "Emergency Kill" switch does not display "ON". Proceed to test step 4.Test Step 3. Check the Status while the "Emergency Kill" Switch is Not Active.
Deactivate the "Emergency Kill" switch.
Observe the status of the "Emergency Kill" switch on the Cat ET.Expected Result:The parameter for the "Emergency Kill" switch should read "OFF".Results:
OK - The "Emergency Kill" switch is functioning correctly.Repair: There may be an intermittent problem. Perform the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" if the problem is intermittent. Stop.
Not OK - The parameter for the "Emergency Kill" switch does not display "OFF". Proceed to test step 4.Test Step 4. Test the Input for the "Emergency Kill" Switch to the ECM.
Turn the circuit breaker CB-8 to the OFF position.
Disconnect ECM connector P1 from the ECM. Remove the socket pins P1-29, P1-02 and P1-20 from ECM connector P1.Note: Disconnecting the common sensor wire from the ECM will generate an open circuit diagnostic code for all sensors that are connected to the sensor common. Troubleshoot the original diagnostic code. Delete the logged diagnostic codes when you are finished.
Insert a wire jumper into the sockets for the wires in P1-29, P1-02 and P1-20, that were removed in the previous step.
Reconnect connector P1 to ECM connector J1.
Turn the circuit breaker CB-8 to the ON position.
Observe the parameters for the "Emergency Kill" switch on the Cat ET.
Turn the circuit breaker CB-8 to the OFF position.
Locate a suitable jumper wire and connect P1-02 and P1-20 to P1-29.
Turn the circuit breaker CB-8 to the ON position.
Observe the parameters for the "Emergency Kill" switch on the Cat ET.
Turn the circuit breaker CB-8 to the OFF position.
Remove the wire jumpers. Replace all wires and reconnect all connectors.Expected Result:The parameter for the "Emergency Kill" switch should display "OFF" when the jumper is installed. The parameter for the "Emergency Kill" switch should display "ON" when the jumper is removed.Results:
OK - The parameter for the "Emergency Kill" switch is displaying the proper states. The problem is not with the ECM. Proceed to test step 5.
Not OK - The parameter for the "Emergency Kill" switch is not displaying the proper states.Repair: Replace the ECM. Perform the diagnostic procedure Troubleshooting, "Replacing the ECM". Stop.Test Step 5. Check the Wiring of the "Emergency Kill" Switch Circuit.
Disconnect ECM connector J1/P1.
Install a wire jumper between terminal 2 and terminal 10 on the "Emergency Kill Relay".
Measure the resistance between P1-29 and P1-20.
Measure the resistance between P1-29 and P1-2.
Remove the wire jumper from terminal 2 and terminal 10 on the "Emergency Kill Relay".Expected Result:The resistance should measure less than 10 Ohms.Results:
OK - The resistance measures less than 10 Ohms. Proceed to test step 7.
Not OK - The resistance measures more than 10 Ohms. Proceed to test step 6.Test Step 6. Check the "Emergency Kill" Switch Circuit in the "ADEM Box".
Disconnect ECM connector J1/P1.
Install a wire jumper between terminal 2 and terminal 10 on the "Emergency Kill Relay".
Measure the resistance between terminal 101 and terminal 102 in the "ADEM Box".
Measure the resistance between terminal 101 and terminal 123 in the "ADEM Box".
Measure the resistance between terminal 101 and terminal 127 in the "ADEM Box".
Remove the wire jumper from terminal 2 and terminal 10 on the "Emergency Kill Relay". Reconnect ECM connector J1/P1.Expected Result:The resistance should measure less than 10 Ohms for each measurement.Results:
OK - The resistance measures less than 10 Ohms for each measurement.Repair: The wiring and/or the connectors between the "ADEM Box" terminals 101 and 127 and the ECM connector P1 need repair. Repair the connectors and/or wiring or replace the connectors and/or wiring. Stop.
Not OK - The resistance measures more than 10 Ohms on one of the measurements.Repair: Check the component and/or the terminal before the incorrect resistance measurement. Repair the faulty component or replace the faulty component. Refer to Illustration 1. Stop.Test Step 7. Check the Normally Closed Contacts on the "Emergency Kill Relay".
Remove the wire from terminal 2 of the normally closed contacts of the "Emergency Kill Relay".
Ensure that the main disconnect switch is in the ON position.
Turn the circuit breaker CB-8 to the ON position.
Activate the "Emergency Kill" switch.
Measure the resistance between the normally closed contacts on terminal 2 and terminal 10 of the "Emergency Kill Relay".
Deactivate the "Emergency Kill" switch. Reconnect the wire that was removed from terminal 2 of the "Emergency Kill Relay".Expected Result:The resistance should be greater than 20,000 Ohms when the "Emergency Kill Switch" is activated.Results:
OK - The resistance


Parts cotter Mariner:

82126M
 
82126M COTTER PIN
7002207, 7015327, 7048227, 7048321, 7055324, 7055524, 7060522
82053M
 
82053M COTTER PIN
7003207, 7005207, 7005227, 7048227, 7048321, 7055324, 7055524, 7060522, 7115F13RD, 7115F13UF, 7F75412RD, 7F75413TD, 7F75413ZD
82049M
 
82049M COTTER PIN
7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
21071
 
21071 COTTER PIN, SHIFT LINK
7006201CD, 7006201HB, 7008218EW, 7008237, 7010207HB, 7015201LD, 70152374D, 7020201NC, 7020207, 7031203GD, 7031207CD, 7031207LF, 7041203GB, 70432037D, 7043213HD, 7090529, 7115528, 7115529, 7140528, 7140629, 7F25203JB, 7F30203HD, 7F40452KD, 7F40452LB,
84301M
 
84301M COTTER PIN
7010209, 7015529
826988M
Back to top