19167M Mariner COVER (STARBOARD)


19167M COVER (STARBOARD) Mariner 7040206, 7040706, 7040716, 7055324, 7055524 COVER
19167M COVER (STARBOARD) Mariner
Rating:
53

Buy COVER (STARBOARD) 19167M Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$154.70
 

01-10-2017

InvisibleM: InvisibleMask
P#:2012-DODGE-RAM 19167M Clear Bra Paint Protection Film Kit for a DODGE RAM LARAMIE 1500 . Coverage includes a Hood Fender Mirror Kit (3M Scotchgard Film)
3M Scotchgard film specifically cut for a 2012 DODGE RAM LARAMIE 1500||Coverage includes pre-cut paint protection film listed in the title.||Comes with a professional squeegee, squirt bottles, instruction DVD, knife, microfiber cloth and door edge guards||Protect your vehicles paint finish with our computer cut clear-coated paint protection films. InvisibleMask clear bra kits are precisely pre-cut to fit the contours of your car.||InvisibleMask products will protect your vehicle from bugs, dirt, scratches, nicks, road salt, sand and road debris and will cause no damage to your OEM paint if removed years later.
Number on catalog scheme: 62
 

Compatible models:

Mariner entire parts catalog list:

7040206 1986,1987,1988,1989
7040706 1986,1990,1992
7040716 1986
7055324 1984,1985,1988,1989
7055524 1984,1985

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) T400011 Crankshaft Turning Tool 1
A(2) 27610291 Housing 1
27610289 Engine Turning Tool 1
B - E12 Torx Socket 1
C 21825607 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g06362599
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod.Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin.Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g06360869
Install connecting rod cap (2) to connecting rod (3).Note: Ensure that etched Number (Y) on connecting rod cap (2) matches etched Number (Y) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Use Tooling (B) tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) and Tooling (C) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings.Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.
If the glow plugs were removed, install the glow plugs. Ref to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.


Parts cover Mariner:

41882M
 
41882M COVER
7004201, 7005201, 7005207, 7008204, 7008208, 7008218EW, 7008226, 7008305, 7008425, 7010209, 7015327, 7015529, 7020201, 7025200, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030301, 7040202, 7040206, 7040207PW, 7040716, 7055324
80246M
 
80246M COVER... .
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7015207, 7015307, 7015327, 7025207NW, 7025207PW, 7030301, 7040206
81395M
 
81395M COVER
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83047M
 
83047M COVER, BOTTOM
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
81330M
 
81330M COVER, EXHAUST - OUTER
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060528
92651M
 
92651M COVER, SHOCK MOUNT
7048227, 7048321, 7055324, 7055524, 7060507, 7060522
97703M
 
97703M COVER, CYLINDER HEAD
7040202, 7040206, 7040706, 7040716
97705M
 
97705M COVER, THERMOSTAT
7040202, 7040206, 7040207PW, 7040706, 7040716
Back to top