70679 Mariner COVER, UPPER AND LOWER SHOCK MOUNTING PIN


70679 COVER, UPPER AND LOWER SHOCK MOUNTING PIN Mariner 7050200, 7050716, 7070520, 7080629, 7085507, 7090520, 7115520 COVER
70679 COVER, UPPER AND LOWER SHOCK MOUNTING PIN Mariner
Rating:
38

Buy COVER, UPPER AND LOWER SHOCK MOUNTING PIN 70679 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 55
 

Compatible models:

Mariner entire parts catalog list:

7050200 1980,1982,1983,1985,1986
7050716 1986
7070520 1980,1982,1983
7080629 1979,1980
7085507 1977
7090520 1980
7115520 1980

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     6V-3145     Load Leveler     1    Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
At operating temperature, the hydraulic oil is hot and under pressure. Hot oils can cause burns.To prevent possible personal injury, release the pressure in the implement hydraulic circuit (boom, stick, bucket, and swing), travel circuits, and the hydraulic oil tank at the filler cap before any hydraulic lines or components are disconnected or removed.Remove the filler cap only when the engine is stopped and the filler cap is cool enough to touch.
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.Remove the fill cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact the skin.Be sure that the engine and components are cool enough to touch with your bare hand prior to performing any service work.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification on all lines, hoses, wires, and tubes for installation purposes. Use caps and plugs on all lines, hoses, and tubes in order to prevent fluid loss or contamination of the systems.
Open the engine hood.
Tilt the cab upward.Reference: Operation and Maintenance Manual, SEBU7197, "Cab Tilting"
Lower the bottom guard.Reference: Operation and Maintenance Manual, SEBU7197, "Bottom Guard Lowering"
Drain the hydraulic oil tank into a suitable container. The capacity of the hydraulic oil tank is 80 L (21 US gal).Reference: Operation and Maintenance Manual, "Hydraulic System Oil - Change".
Drain the power train oil tank into a suitable container. The capacity of the power train oil tank is 30 L (8 US gal).Reference: Operation and Maintenance Manual, "Power Train Oil - Change".
Illustration 1 g00620484
Turn battery disconnect switch (2) and secondary disconnect switch (1) to the OFF position.
Remove two bolts (3) and move the mounting plate away from the engine.
Drain the cooling system. The capacity of the cooling system is 24 L (6.3 US gal).
Illustration 2 g00822165
Remove eight bolts (4) from fan guard (5). Remove fan guard (5) .
Illustration 3 g00822202
Remove four bolts (6) which hold fan (7) in place. Remove fan (7) .
Illustration 4 g00822214
Loosen hose clamp (8) and hose clamp (9) .
Disconnect hose assembly (10) and hose assembly (11) from the radiator.
Illustration 5 g00822216
Loosen hose clamp (13). Remove hose assembly (12) .
Remove two bolts (14) which hold the bracket for the expansion tank in place. Remove the expansion tank.


Parts cover Mariner:

74303
 
74303 COVER, AIR INLET
7075524, 7080508, 7080629, 7085507
39667
 
39667 COVER, NYLON - SHIFT CABLE
7070509, 7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
77885
 
77885 COVER, FUEL PUMP
7080508, 7085507
52699
 
52699 COVER, GEAR HOUSING
7002201DK, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7140528, 7140629, 7150453ND, 7150453PD, 7175413AD
99642
 
99642 COVER, MANIFOLD
7045217, 7050717, 7060312PC, 7075312ND, 7075312SD, 7075524, 7075717, 7090524, 7100412NC, 7115520, 71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727
88926
99525A 1
 
99525A 1 COVER ASSEMBLY
7045217, 7050200, 7050716
Back to top