81616M Mariner COVER, WATER INLET-STARBOARD


81616M COVER, WATER INLET-STARBOARD Mariner 7020201, 7025200, 7025500, 7028207, 7028527, 7030200 COVER
81616M COVER, WATER INLET-STARBOARD Mariner
Rating:
38

Buy COVER, WATER INLET-STARBOARD 81616M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 63
 

Compatible models:

Mariner entire parts catalog list:

7020201 1981
7025200 1980
7025500 1980
7028207 1977
7028527 1977
7030200 1980

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Pry Bar 1 Start By:
Remove the rocker shaft assembly.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01130566
Disconnect harness assembly (2) from electronic unit injector (5).
Remove bolt (1) and electronic unit injector clamp (3).
Remove plug (4) from the cylinder head.
Place an identification mark on the electronic unit injector for installation purposes. Each electronic unit injector must be reinstalled in the original location in the cylinder head.
Illustration 2 g01130569
Use Tooling (A) to remove electronic unit injector (5) from the cylinder head.
Remove O-ring seal (6) and O-ring seal (7) from the electronic unit injector. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 9U-6862 Tapered Brush 1
C 4C-5027 Tap Wrench 1
D 4C-6774 Vacuum Gun Kit 1
E 1P-0808 Multipurpose Grease -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01130613
Use Tooling (B) to clean the bore for the electronic unit injector in the cylinder head. Hold Tooling (B) with Tooling (C). Rotate Tooling (B) against Surface (X) of the bore. Continue cleaning until Surface (X) is smooth and shiny.
Use Tooling (D) to remove the fuel from the cylinder. Evacuate as much fuel as possible from the cylinder before installing the electronic unit injector. Several evacuations may be necessary.
Illustration 4 g01130615
Install O-ring seal (6) and O-ring seal (7) on the electronic unit injector.
Apply Tooling (E) to the bore of the cylinder head for the electronic unit injector.
When an electronic unit injector is replaced, the new electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new electronic injector code is not entered, the characteristics of the previous electronic unit injector is assumed.If it is not possible to immediately reprogram the electronic injector code into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance.
Position electronic unit injector (5) into the original location in the cylinder head. Center the solenoid between the valve springs. Press the electronic unit injector into the cylinder head. Do not strike the electronic unit injector.
Illustration 5 g01130566
Install plug (4) in the cylinder head.
Install electronic unit injector clamp (3) and bolt (1). Tighten bolt (1) in order to seat electronic unit injector (5) in the cylinder head. Do not strike the electronic unit injector. Tighten bolt (1) to a torque of 65 7 N m (48 5 lb ft).
Connect harness assembly (2). Tighten the terminal nuts to a torque of 2.5 0.25 N m (22 2 lb in). End By:
Install the rocker shaft assembly.


Parts cover Mariner:

82658M
 
82658M COVER, THERMOSTAT...
7008238, 7008247, 7028207, 7028527
81030M
 
81030M COVER, THERMOSTAT...
7008238, 7008247, 7020201, 7025200, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
81569M
 
81569M COVER EXHAUST-OUTER
7020201, 7025200, 7025500, 7026226, 7028207, 7028527, 7048321
81568M
COVER, EXHAUST-INNER
81568M COVER, EXHAUST-INNER
7020201, 7025200, 7025500, 7026226, 7028207, 7028527
80703M
 
80703M COVER, DRIVE END
7028207, 7028527
84920M
 
84920M COVER, FRONT
7025200, 7025500, 7028527, 7030200
96362M
COVER, FRONT
96362M COVER, FRONT
7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030320, 7040202, 7040206, 7040716
84928M
 
84928M COVER, REAR
7025200, 7025500, 7028527, 7030200
Back to top