83091M Mariner COVER, WATER INLET...


83091M COVER, WATER INLET... Mariner 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425 COVER
83091M COVER, WATER INLET... Mariner
Rating:
78

Buy COVER, WATER INLET... 83091M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mariner entire parts catalog list:

7008208 1978
7008218EW 1996,1998
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     6V-6192     Pliers     1    
B     7M-3978     Ring Expander     1    
C     5P-8639     Hydraulic Press (Connecting Rod Bearing)     1    
8F-0024 Hose Assembly     1    
1P-2375 Connecting Coupler     1    
1P-2376 Connecting Coupler     1    
5P-8651 Spacer     1    
5P-8649 Adapter     1    
5P-8650 Bushing Adapter     1    
- Hydraulic Pump     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00786693
Illustration 2 g00507526
Install piston pin bearing (6) in connecting rod (4) , as follows:Note: The old bearing is pushed out by Tool (C) as the new bearing is installed.
Illustration 3 g00570892
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Heat length (Y) of connecting rod (4) to a temperature of 175 to 260 °C (347 to 468 °F). (Y) Maximum length for heating the connecting rod ... 85.0 mm (3.35 inch)
Use Tool (C) to remove the old bearing and install the new bearing at the same time. The adapter of Tool (C) should make full contact with the surfaces of the connecting rod.Note: Orient the bearing joint within 5 degrees of either location (X) .
Allow the connecting rod and the bearing to cool to room temperature.
Use a pin boring machine to machine the bore of the piston pin bearing to the correct diameter.Diameter of piston pin bore ... 50.830 .008 mm (2.0012 0.0003 inch)
Check the clearance between the ends of the piston rings (5) . Refer to Specifications, "Pistons And Rings" for additional information.Note: The oil ring is installed over the spring with the oil ring end gap 180 degrees from the oil ring spring joint.
Install the oil ring spring in the oil ring groove of the piston.
Illustration 4 g00507525
Install the oil ring on the piston with Tool (B) .
Use Tool (B) to install the intermediate piston ring with the side that has the identification "UP-2" toward the top of the piston.
Use Tool (B) to install the top piston ring with the side that has the identification "UP-1" toward the top of the piston.
Position the piston rings so the end gaps are 120 degrees from each other.
Put piston crown (7) in position on piston skirt (8) .
Put the piston in position on connecting rod (4) . Apply clean engine oil on piston pin (2) and install the piston pin. Install retainer rings (1) with Tool (A) . Ensure that the retainer rings are fully seated in the grooves of the piston.Note: Ensure that the bearings are installed so that the bearing tabs fit into the notch in the connecting rod and the connecting rod cap.
Install connecting rod bearings (3) in the connecting rod and the connecting rod cap.End By: Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts cover Mariner:

80430M
 
80430M COVER...
7008238, 7008247
82892M
COVER... .
82892M COVER... .
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
81065M
COVER, SWIVEL BRACKET...
81065M COVER, SWIVEL BRACKET...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
82638M
 
82638M COVER, PUMP
7008208, 7008238, 7008248
84266M
 
84266M COVER, PUMP
7008208, 7008238, 7008248, 7008305, 7010209, 7015529, 7040208PW
95598M
 
95598M COVER, Exhaust, Outer
7008218EW, 7008305, 7008425
94745M
 
94745M COVER
7008218EW, 7008425
42089A 2
 
42089A 2 COVER ASSEMBLY
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 7016207CD, 7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD
Back to top