41309M Mariner DECAL


41309M DECAL Mariner 7048321, 7055324 DECAL
41309M DECAL Mariner
Rating:
73

Buy DECAL 41309M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

Compatible models:

7048321   7055324   Mariner

Mariner entire parts catalog list:

7048321 1981
7055324 1984,1985,1988,1989

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 8S-2328 Dial Indicator 1
C 334-0519 Grease -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00577390
If crankshaft gears (6) were removed, install crankshaft gears (6) on the crankshaft and install bolts (7).
Check the clearance of the bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure.
Illustration 2 g01353563Note: Place clean engine oil on the main bearings and on the connecting rod bearings prior to installation.Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies.
Illustration 3 g01353615
Typical example
Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach a suitable lifting device to crankshaft (4) and position the crankshaft in the cylinder block. The weight of crankshaft (4) is approximately 762 kg (1680 lb).
Illustration 4 g01353620
Tightening sequence
Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Place Tooling (C) on the bolts for the main bearing caps.
Illustration 5 g01353682
Place clean engine oil on thrust plates (3). Install thrust plates (3) on each side of the center main bearing.
Place main bearing caps (5) into position and install the bolts. Tighten the bolts in the numerical sequence that is shown above to a torque of 190 14 N m (140 10 lb ft). Tighten the bolts again for an additional 180 5 degrees.
Check the end play with Tooling (B). The end play must not exceed 0.40 0.23 mm (0.016 0.009 inch).
Illustration 6 g01353696
Position the connecting rods on the journals of the crankshaft. Install connecting rod bearing caps (2). Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 7 g01353701
Tightening sequence
Place Tooling (C) on the bolts for the connecting rod caps and install the bolts.
Tighten the bolts with the following steps:
Tighten bolts (14) and (15) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (14) and (15) again to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn). An impact wrench may be used.
Place the remaining connecting rod caps in position and tighten the bolts with the same procedure that is in Steps 12.a through 12.e.
Illustration 8 g01353745
Each counterweight is numbered and must be installed in the same position as the corresponding number on the crankshaft mounting pad in order to prevent damage to the crankshaft.
Install counterweights (1).
The following procedure is for the installation of the counterweights in G3516 Engines.
Ensure that the dowels are in the correct position and install the counterweights on the crankshaft.
Apply Toolin


Parts decal Mariner:

75881
 
75881 DECAL, FUEL TANK
7008204, 7008208, 7008226, 7008238, 7008248, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7060507, 7060522, 7060528, 7070509, 70805
83710M
 
83710M DECAL, REAR
7048207, 7048227, 7048321
82865M
 
82865M DECAL, SIDE SET
7048207, 7048227, 7048321, 7060507, 7060528
97099M
 
97099M DECAL
7048227, 7048321
97797M
 
97797M DECAL, FRONT
7048227, 7048321, 7055524, 7060522
98941M
14282M
 
14282M DECAL
7055324
95623M
 
95623M DECAL
7055324
Back to top