43191A84 Mariner DECAL SET (BROWN) (MERC 60)


43191A84 DECAL SET (BROWN) (MERC 60) Mariner 7050716, 7060312PC, 7060524 DECAL
43191A84 DECAL SET (BROWN) (MERC 60) Mariner
Rating:
53

Buy DECAL SET (BROWN) (MERC 60) 43191A84 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

Mariner entire parts catalog list:

7050716 1986
7060312PC 1989
7060524 1984,1985,1986,1989,1990

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 589-7433 Link Bracket 2
B - Loctite ® C5-A (North America) -
Loctite ® 8008 (Outside North America) -
C 207-1601 Rubber Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the spacer plate and the surface of the cylinder block are clean.
Illustration 1 g06553514
Ensure that the surface of the spacer plate gasket and the surface of the cylinder block are clean. Do not use a gasket adhesive on these surfaces.
Install a new gasket (18) on the dowels in the cylinder block.
Install O-ring seal (19).
Illustration 2 g06553497
Install spacer plate (17) and cylinder head gasket (16) on the dowels in the cylinder block.
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection" for the correct procedure.
Illustration 3 g06553298
Install seals (13) and seals (14).
Apply Tooling (C) to the bore of the inlet tube assembly. Install O-ring seal (11) in the inlet tube assembly.
Install gasket (12) on the exhaust manifold.
Install O-ring seal (15) on the dowel.
Illustration 4 g06554112
Install plug (20).
Illustration 5 g06554127
Install Tooling (A) onto cylinder head assembly (10). Attach a suitable lifting device to Tooling (A). The weight of cylinder head assembly (7) is approximately 47 kg (104 lb).
Ensure that the bottom of the cylinder head assembly is thoroughly clean.
Illustration 6 g06552788
Lift the cylinder head assembly into position on the cylinder block. Install bolts (8) and bolts (9) according to the instructions in Step 15 or Step 16.Note: Only 216 mm (8.5 inch) bolts (8) can be used for the following torque procedures.Note: Refer to Specifications, "Cylinder Head".
Remove Tooling (A) from the cylinder head.
Illustration 7 g06554187
Tightening sequence with 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).Note: Refer to Illustration 7 for the correct tightening sequence.
Coat the threads of the bolts with clean engine oil.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Turn bolt (1) through bolt (8) an angle of 180 5 degrees.
Tighten bolts (9) and (10) to a torque of 55 10 N m (40 7 lb ft).
Illustration 8 g06554195
Tightening sequence with 110-6991 Cylinder Head Gasket (Cellulose) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).Note: The cellulose head gasket cannot be used with an iron spacer plate.Note: Refer to Illustration 8 for the correct tightening sequence.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 200 15 N m (148 11 lb ft).
Tighten bolt (1) through bolt (8) again to a torque of 200 15 N m (148 11 lb ft).
Turn bolt (1) through bolt (8) to an angle of 180 degrees.
Tighten bolt (9) and bolt (10) to a torque of 55 10 N m (41 7 lb ft).


Parts decal Mariner:

93151A81
13483A86
 
13483A86 DECAL SET (SILVER)(MERC 60)
7050716, 7060312PC, 7060524
11622A85
 
11622A85 DECAL SET (MARINER 60)
7050716, 7060312PC, 7060524
43538A86
 
43538A86 DECAL SET (MERC 50)
7050716, 7060312PC, 7060524
11622A86
 
11622A86 DECAL SET (MARINER 50)
7050716, 7060312PC, 7060524
43598A87
810464A90
816117A90
Back to top