808525A03 Mariner DECAL SET


808525A03 DECAL SET Mariner 7006201HB, 7006201TB, 7015201LD DECAL
808525A03 DECAL SET Mariner
Rating:
28

Buy DECAL SET 808525A03 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 0
 

Compatible models:

Mariner entire parts catalog list:

7006201HB 1999,2000,2001,2002,2003,2004
7006201TB 2005,2006
7015201LD 2002

Information:


Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g06451609
Illustration 2 g06451649
Disconnect engine harness assembly (6) for Exhaust Gas Recirculation (EGR) valve (5).
Protect starter motor (7) and the engine harness from coolant when EGR valve (5) is removed.
Reposition hose clamp (12) and disconnect hose (11) from EGR valve (5).
Remove bolts (10) from EGR valve (5).
Remove bolts (4) from EGR valve (5). Support the EGR valve as the bolts are removed.
Remove EGR valve (5) from exhaust gas cooler (NRS) (9) and exhaust manifold (3).
Remove gasket (1) (not shown) and gasket (2) (not shown).
Remove O-ring seal (8) (not shown).Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Anti-Seize Compound 1
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Inspect inside the exhaust gas recirculation valve for deposits or debris. Use a suitable clean lint free cloth with a suitable engine cleaner to clean inside the exhaust gas recirculation valve.
Illustration 3 g06451609
Illustration 4 g06451649
Clean the gasket surfaces of exhaust gas recirculation valve (5).
Install new O-ring seal (8) to EGR valve (5)
Apply Tooling (A) to bolts (4) and bolts (10).
Position new gasket (1) (not shown) and new gasket (2) (not shown) onto exhaust gas recirculation valve (5). Ensure that the gaskets are correctly orientated.
Position exhaust gas recirculation valve (5) onto exhaust manifold (3) and exhaust gas cooler (NRS) (9).
Install bolts (4) and bolts (10) finger tight.Tighten bolts (4) to a torque of 22 N m (194.72 lb in)Tighten bolts (10) to a torque of 11 N m (97.36 lb in)
Install hose (11) onto EGR valve (5).
Slide hose clamp (12) into position and tighten the hose clamp securely.
Connect harness assembly (6) to EGR valve (5).
Ensure that starter motor (7) and the engine wiring harness assembly is dry.
Turn the battery disconnect switch to the ON position.
After replacement of the exhaust gas recirculation valve, the exhaust gas recirculation valve must be


Parts decal Mariner:

12869
 
12869 DECAL (TILT)
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 7016207CD, 7F08203HF, 7F08261DF
816291A96
 
816291A96 DECAL SET
7010207HB, 7010312DT, 7015201LD
12970 1
 
12970 1 DECAL, Bezel Choke
7006201HB, 7006201TB, 7010207HB, 7011201TB, 7015201LD
856985A 3
 
856985A 3 DECAL-EPA INFORMATION
7006201HB, 7015201LD
808522A00
 
808522A00 DECAL SET
7006201HB, 7015201LD
808526A00
 
808526A00 DECAL SET
7006201HB, 7006201TB, 7015201LD
808546A01
 
808546A01 DECAL SET
7006201HB, 7015201LD
808560A01
 
808560A01 DECAL SET
7006201HB, 7015201LD
Back to top