879753A01 Mariner DECAL SET


879753A01 DECAL SET Mariner 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD DECAL
879753A01 DECAL SET Mariner
Rating:
58

Buy DECAL SET 879753A01 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

Mariner entire parts catalog list:

7F40452KD 2001
7F40452LB 2002
7F41452KB 2001,2002
7F41452KD 2001

Information:


Illustration 1 g06035973
Table 1
Specifications for 263-1852 Connecting Rod Gp, 348-7288 Connecting Rod Gp, 482-8753 Connecting Rod, and 482-8756 Connecting Rod
Item Qty Part Specification Description
A - - Piston pin bushing bore 130.00 0.015 mm (5.1181 0.0006 inch)
B - - Distance between center of bearings is 600 mm (23.6 inch)
C - - Bore in connecting rod for crankshaft bearing is 225 0.015 mm (8.8583 0.0006 inch) after the connecting rod cap has been installed and torqued.
1 1 4P-6125 Bushing(1) The connecting rod temperature may be raised to 190° 15°C (342° 27°F) to install the bushing.
Note: Do not use a torch to heat the connecting rod.
The piston pin bushing temperature may be lowered to −90° C (−130° F) to install the bushing into the connecting rod piston pin bore.
Lubricate the piston pin with clean engine oil prior to installation.
(1) Machining is required after piston pin bushing is installed
Illustration 2 g06035975
Positioning piston pin bearing
Table 2
Item Qty Part Specification Description
D 1 4P-6125 Bushing The bearing junction and the locating hole are 180 degrees across from each other. The bearing junction and the locating hole must be assembled within area (D). Area (D) is 15 degrees from the horizontal centerline of the connecting rod piston pin bore.
Illustration 3 g06046096
(E) Torque Turn Rod
(F) Hydraulic Tensioned Rod
Table 3
Item Qty Part Specification Description
2 4 467-0537 Bolt As Tighten the bolts for a maximum of five times. The reuse includes the retightening after checking the rod bore or bearing clearance. Do not reuse the connecting rod nuts. An overloaded bolt can be detected by threading a new 205-0640 Nut onto the bolt by hand. If the threads are not damaged, the nut will easily reach the end of the bolt thread with light finger pressure. If the nut stops before reaching the end, do not reuse the bolt.
3 4 463-9619 Bolt The 463-9619 Special Bolt As and 463-9626 Nut may be reused if they meet reuse guidelines. An overloaded or damaged bolt can be detected by threading a new 463-9626 nut on the bolt by hand. If the threads are not damaged, the nut will easily reach the end of the bolt thread with light finger pressure. If the nut stops before reaching the end, do not reuse the bolt.
Illustration 4 g03359716
Table 4
Connecting Rod Bolt Tightening Procedure for 263-1852 Connecting Rod Gp, and 348-7288 Connecting Rod Gp
Item Qty Part Specification Description
- 4 205-0640 Nut
1. Lubricate the bolt threads, bolt shank, and nut seating faces of cap and nut with Bel-Ray Molylube 67700.
2. Tighten all four nuts by hand until the nuts contact the face of the cap. No resistance should be felt that would indicate thread damage or debris in the joint. If the nuts and/or nuts cannot be threaded by hand, the nuts and/or bolts must be replaced. Do not use an impact wrench to install the nuts up to the face of the cap.
Note: Nuts (1) and (2) are on the tab side of the connecting rod cap.
3. Sequentially tighten nuts (1) and (4) to 105 15 N m (75 10 lb ft).
4. Sequentially tighten nuts (2) and (3) to 105 15 N m (75 10 lb ft).
5. Tighten nuts (1) and (4) sequentially to 340 15 N m (250 11 lb ft).
6. Tighten nuts (2) and (3) sequentially to 340 15 N m (250 11 lb ft).
7. Again tighten nuts (1) and (4) sequentially to 340 15 N m (250 11 lb ft).
8. Again tighten nuts (2) and (3) sequentially to 340 15 N m (250 11 lb ft).
8. Turn nuts (1) and (4) sequentially to 180 5 degrees.
9. Turn nuts (2) and (3) sequentially to 180 5 degrees.
Illustration 5 g06170356


Parts decal Mariner:

830253
 
830253 DECAL-TILT/LOCK
7031203GD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207HB, 7055207TF, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7U
824093 16
 
824093 16 DECAL-SHIFT
7031203GD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7A30453VZ, 7A40302UD, 7A40302ZZ, 7A40312UZ, 7A40312ZZ, 7A40412ZZ, 7A41412LB, 7A41452I
856985A22
 
856985A22 DECAL-EPA INFO
7F30203HD, 7F40452KD
804654A00
 
804654A00 DECAL-EPA INFO
7F30203HD, 7F40452KD
803946A99
 
803946A99 DECAL SET
7F30203HD, 7F30203LB, 7F40452KD, 7F40452LB
803947A99
 
803947A99 DECAL SET
7F30203HD, 7F30203LB, 7F40452KD, 7F40452LB
804655A01
 
804655A01 DECAL, EPA Label Information
7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD
803640A05
 
803640A05 DECAL SET
7F30203LB, 7F40452LB
Back to top