8M0012082 Mariner DECAL, Tiller Handle Shift


8M0012082 DECAL, Tiller Handle Shift Mariner 7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK DECAL
8M0012082 DECAL, Tiller Handle Shift Mariner
Rating:
83

Buy DECAL, Tiller Handle Shift 8M0012082 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Compatible models:

Mariner entire parts catalog list:

7A25203UK 2006,2010
7A25213UL 2006
7A25302UL 2006
7A3G312UK 2006

Information:


Typical Example1. Remove bolts (1) from the alternator bracket.2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor (if equipped). Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See the topic, Remove & Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019P4. a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 bl ft).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb ft).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb ft) by hand.d. Install the rocker shaft assemblies and push rods. See the topic, Install Rocker Shaft Assemblies & Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb ft).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb ft). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb ft).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in) for intake and 0.76 mm (.030 in) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb ft).5. Install the valve cover bases and the inner fuel lines. See the topic, Install Rocker Shaft Assemblies & Push Rods.6. Install the valve covers. See the topic, Install Valve Covers.
Typical Example7. Install plate (4).8. Connect the water line to the air compressor (if equipped).9. Install bolts (5) for the alternator bracket.End By:a. install exhaust manifoldb. install fuel injection linesc. install aftercooler housingd. install water temperature regulatore. install rocker shaft assemblies and push rods


Parts decal Mariner:

823701004
 
823701004 DECAL, Co-Pilot
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
892904005
 
892904005 DECAL, Oil Pressure
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB
859278003
 
859278003 DECAL, Throttle Only
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
859278004
 
859278004 DECAL, Start
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
892904006
 
892904006 DECAL, Tiller Lock Release
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
8M0012079
 
8M0012079 DECAL, Shift
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
898101202
 
898101202 DECAL, Throttle-Lock
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
896853A06
 
896853A06 DECAL SET
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
Back to top