94260A81 Mariner DECAL SET (DARK GRAY COWLS)(MARINER 50)


94260A81 DECAL SET (DARK GRAY COWLS)(MARINER 50) Mariner 7050200, 7050716 DECAL
94260A81 DECAL SET (DARK GRAY COWLS)(MARINER 50) Mariner
Rating:
73

Buy DECAL SET (DARK GRAY COWLS)(MARINER 50) 94260A81 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

7050200   7050716   Mariner

Mariner entire parts catalog list:

7050200 1980,1982,1983,1985,1986
7050716 1986

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336430
Typical example
Ensure that cooler matrix (19) is clean and free from damage. Ensure that spacer plate (17) is clean and free from damage. Replace any damaged components.
Position a new joint (18) onto spacer plate (17). Install cooler matrix (19) to the spacer plate.
Install bolts (15) finger tight.
Illustration 2 g01336427
Typical example
Position brackets (5), (10) and (14) onto the assembly of oil cooler (6). Install bolts (7). Note: Ensure that brackets for the tube assemblies are installed in the correct location and the correct orientation. The bolts are different lengths. Ensure that the different bolts are installed in the correct location.
Install new joint (16) to the assembly of oil cooler (6). Push bolts (7) through the holes in the joint. Note: The holes in the joint have serrations that hold the bolts captive.Installation Procedure (Engine Oil Cooler with a Low Mounted Filter Base)
Clean the mating surfaces of the cylinder block.
Illustration 3 g01417038
Typical example of an engine oil cooler with a blanking plate
Install the assembly of oil cooler (6) to the cylinder block. Tighten bolts (7) finger tight.
Illustration 4 g01336468
Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base
Tighten bolts (7) to a torque of 22 N m (16 lb ft) in the sequence that is shown in Illustration 4.
If the engine has a low mounted oil filter on the left hand side, install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install". If the engine has a right hand side oil filter, follow Steps 4.a through 4.d in order to install blanking plate (12).
Install bolts (11) to blanking plate (12).
Position a new joint onto blanking plate (12).
Install the assembly of the blanking plate to the assembly of oil cooler (6).
Tighten bolts (11) to a torque of 22 N m (16 lb ft).
Remove the plugs from tube assembly (9). Remove the caps for the fuel return from the cylinder head and from transfer pump (8). Install tube assembly (9) to the cylinder head and to transfer pump (8).
Follow Steps 6.a through 6.e in order to connect engine wiring harness (4).
Place the harness in position.
Connect engine wiring harness (4) to position sensor (2) for the fuel injection pump.
Connect engine wiring harness (4) to oil pressure sensor (13).
Connect engine wiring harness (4) to solenoid (1) for the fuel injection pump.
Install new cable straps in order to secure engine wiring harness (4) to the assembly of oil cooler (6).
Remove the plugs from all plastic tube assemblies (3). Remove the caps from the appropriate ports. Install plastic tube assemblies (3).
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure. End By:
Install the bracket for the Electronic Control Module. Refer to Disassembly and Assembly, "ECM Bracket - Remove and Install".


Parts decal Mariner:

93151A81
43198A84
13482A86
 
13482A86 DECAL SET (MERC 45)
7050200, 7050716
11621A86
43191A84
 
43191A84 DECAL SET (BROWN) (MERC 60)
7050716, 7060312PC, 7060524
13483A86
 
13483A86 DECAL SET (SILVER)(MERC 60)
7050716, 7060312PC, 7060524
11622A85
 
11622A85 DECAL SET (MARINER 60)
7050716, 7060312PC, 7060524
Back to top