95570M Mariner DECAL


95570M DECAL Mariner 7002200, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205 DECAL
95570M DECAL Mariner
Rating:
13

Buy DECAL 95570M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

Mariner entire parts catalog list:

7002200 1980,1985,1988,1989
7020201 1981
7025200 1980
7025500 1980
7026226 1986,1988
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990

Information:

Introduction
This Special Instruction provides the procedure to repower a 772, 773, and 775B Off-Highway Truck. The replacement engine will be a Tier I 3412 engine. The 772, 773 and 775B Off-Highway Truck was originally equipped with a 3412 engine. The original 3412 engine is not regulated for emissions. This Special Instruction will provide the information in order to install the Tier I level replacement engine.
Table 1
Engine Arrangement
Original Engine Replacement Engine
1W-0773
103-7416
4N-7826 212-2234 (1)
10R-1177 (2)
(1) New Repower Engine
(2) RemanThis Special Instruction does not include procedures that can be found in your existing manuals. Refer to the original Service Manual, Parts Manual, and Operation and Maintenance Manual for more information.When you have completed this procedure, prepare the machine for service. Refer to the Operation and Maintenance Manual.Note: Do not perform any procedure in this Special Instruction until the information has been read and understood.Reference: Service Manual, Parts Manual, Operation and Maintenance Manual.This instruction contains some procedures that come from dealer feedback. The emissions replacement engine is not a direct replacement. Additional parts and labor hours may be needed to complete this engine replacement. Variations in machine serial number breaks or options could cause a discrepancy in the modifications, required parts, and labor hours. This documentation is a guideline for Cat dealer personnel in order to complete the repower procedure. If errors are found, contact the Caterpillar Emissions Solutions Group. This list is the information that will be required:
Machine serial #
Original engine arrangement #
Emissions engine arrangement #
Original engine serial #
Details of the error
Photos of error and photos after the proposed solutionRegister the Retrofit
Reference: Special Instruction, REHS5097, "Instructions to Register the Retrofit"Documenting changes to a machine configuration is an advantage to Caterpillar and the dealer technicians that are sent to repair a machine. By identifying that the machine has been reconfigured, the technician will have a better opportunity to have the correct parts, tooling, and service information. Identifying that the machine has been reconfigured will also allow Caterpillar to include the retrofitted serial numbers in applicable Service Letters.Safety
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Do not attempt to assemble this machine until you read and you understand the assembly instructions.Improper assembly procedures could result in injury or death.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Welding on Electronically Controlled Engines
Proper welding procedures are necessary to avoid damage to electronic controls. Perform welding on the engine according to the following procedure.
Set the engine control to the "STOP" mode.
Turn OFF the fuel supply to the engine.
Disconnect the negative terminal from the battery.
Disconnect the engine electronic components from the wiring harnesses: ECM, throttle actuator, actuator for the turbocharger compressor bypass, fuel metering valve, and sensors.
Protect the wiring harnesses from welding debris and/or from welding spatter.
Do NOT use electrical components (ECM or sensors) or electronic component grounding points for grounding the welder.
Connect the welder ground cable directly to the engine component that will be welded. Place the clamp within 5.0 mm (0.20 inch) to the weld to reduce the possibility of welding current damage to the engine bearings, electrical components, and engine components.


Parts decal Mariner:

95489M
 
95489M DECAL, TOP (ENGLISH)
7005201, 7005207, 7008204, 7008208, 7008226, 7008305, 7010209, 7015327, 7015529, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040706, 7040716, 7055324, 7055524
81139M
 
81139M DECAL, TRIM-STARBOARD
7028207, 7028527
84888M
 
84888M DECAL, TIMING MARK
7028527, 7030200, 7040202, 7040208, 7040328, 7040716
97778M
95498M
 
95498M DECAL, SIDE (ENGLISH)
7015327, 7020201, 7025200, 7025500, 7028527, 7030200, 7040202, 7040716
95504M
 
95504M DECAL, SIDE (FRENCH)
7010209, 7015327, 7015529, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040706, 7040716, 7055324, 7055524
95674M
 
95674M DECAL, SIDE AND REAR
7030205, 7030301
95675M
 
95675M DECAL, FRONT
7030205, 7030301
Back to top