32325T Mariner DRIVER HEAD TOOL


32325T DRIVER HEAD TOOL Mariner 7200473HD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225E73MD DRIVER
32325T DRIVER HEAD TOOL Mariner
Rating:
18

Buy DRIVER HEAD TOOL 32325T Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mariner entire parts catalog list:

7200473HD 1999
7200473JD 2000
7200473KD 2001,2002
7200D73IY 2006
7200D73MD 2003
7200D73RD 2004,2005,2006
7200D73ZY 2006
7225E73MD 2003,2004

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is not necessary if the measurement of the valve lash is in the acceptable range in Table 1.
Table 1
Inlet Valves Exhaust Valves
Valve Lash (Stopped Engine) 0.38 0.08 mm
(0.015 0.003 inch) 0.76 0.08 mm
(0.030 0.003 inch)
TC Compression Stroke 1-2-4 1-3-5
TC Exhaust Stroke(1) 3-5-6 2-4-6
Firing Order 1-5-3-6-2-4(2)
(1) 360° from TC compression stroke
(2) The No. 1 cylinder is at the front of the engine.If the measurement is not within this range, an adjustment is necessary. Refer to "Valve Lash Adjustment" for the proper procedure.Valve Lash Adjustment
Illustration 1 g01373511
Cylinder and valve location
(A) Exhaust valves
(B) Inlet valvesUse the following procedure to adjust the valve lash:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Table 2
C13 Lash Settings
TC Compression Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.635 0.0762 mm (0.025 0.003 inch)
Cylinders 1-2-4 1-3-5
Table 3
C15 and C18 Lash Settings
TC Compression Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.76 0.08 mm
(0.030 0.003 inch)
Cylinders 1-2-4 1-3-5
Adjust the valve lash according to Table 2 for C13 engines. Adjust the valve lash according to Table 3 for C15 and C18 engines.
Lightly tap the rocker arm with a soft mallet. This action will ensure that the lifter roller seats against the base circle of the camshaft.
Loosen the adjustment locknut.
Place the appropriate feeler gauge between rocker arm and the valve bridge. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve bridge. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the feeler gauge.
Tighten the adjustment locknut to a torque of 30 7 N m (22 5 lb ft). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut.
Remove the timing bolt and turn the flywheel by 360 degrees in the direction of engine rotation. This action will put the No. 6 piston at the top center position on the compression stroke. Install the timing bolt in the flywheel.
Table 4
C13 Lash Settings
TC Exhaust Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.635 0.0762 mm (−.025 0.003 inch)
Cylinders 3-5-6 2-4-6
Table 5
C15 and C18 Lash Settings
TC Exhaust Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.76 0.08 mm
(0.030 0.003 inch)
Cylinders 3-5-6 2-4-6
Adjust the valve lash for C13 engines using Table 4. Adjust the valve lash according to Table 5 for C15 and C18 engines.
Lightly tap the rocker arm with a soft mallet. This action will ensure that the lifter roller seats against the base circle of the camshaft.
Loosen the adjustment locknut.
Place the a


Parts driver Mariner:

37323
 
37323 DRIVER HEAD ROD
7002201DK, 7002201HB, 7002201SK, 7002201UB, 7003201BK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207H
55919
 
55919 DRIVER HEAD
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207HB, 7055207TF, 7115473JD, 7135412ED, 7135412HD, 7135412J
36569
 
36569 DRIVER HEAD
70432037D, 7055207GD, 7075217CD, 7100412CD, 7135412ED, 7135412HD, 7135473GD, 7135473HD, 7150413ED, 7150413HD, 7175423HD, 7200473GD, 7200473HD, 7225412CD, 7225413DD
816244
DRIVER TOOL, Bearing
816244 DRIVER TOOL, Bearing
7200413JD, 7200473GD, 7200473HD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412CD, 7225412HD, 7225413DD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
33491
 
33491 DRIVER
7200413JD, 7200473GD, 7200473HD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412CD, 7225412HD, 7225413DD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
36577T
 
36577T DRIVER CUP
7200413JD, 7200473HD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412HD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
817569T
 
817569T DRIVER TOOL, Oil Seal
7200413JD, 7200473HD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412HD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
859595T
DRIVER, Dual Coil
859595T DRIVER, Dual Coil
7135473KD, 7135D73RD, 7135D73UY, 7135D73ZY, 7200473KD, 7200D73MD, 7200D73RD, 7200D73ZY, 7225E73MD
Back to top