6691A 1 Mariner END CAP ASSEMBLY, LOWER


6691A 1 END CAP ASSEMBLY, LOWER Mariner 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520 END
6691A 1 END CAP ASSEMBLY, LOWER Mariner
Rating:
13

Buy END CAP ASSEMBLY, LOWER 6691A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Compatible models:

Mariner entire parts catalog list:

7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070509 1979
7070520 1980,1982,1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g01349817
Typical example
Disconnect plastic tube assemblies (1) and (8) from fuel injection pump (4).
Disconnect tube assembly (3) from fuel injection pump (4).
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove".
Remove tube assembly (2).
Disconnect the harness assembly from solenoid (7).
Disconnect the harness assembly from solenoid (9).
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Finding Top Centre Position for No.1 Piston".
Use Tooling (B) in order to lock the camshaft in the correct position. Use Tooling (C) in order to lock the crankshaft in the correct position. Refer to Disassembly and Assembly, "Gear Group (Front) - Remove" for the correct procedure.
Remove the backlash from the fuel pump gear. Lock the fuel injection pump in the correct position and remove the fuel pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove and Install" for the correct procedure.
Loosen locking screw (5). Rotate spacer (6) in order to allow locking screw (5) to tighten against the shaft of the fuel injection pump. Rotate the fuel injection pump gear in a counterclockwise direction in order to remove the backlash. Tighten locking screw (5) to a torque of 17 N m (13 lb ft). Note: Locking screw (5) must be tightened in order to prevent the shaft of the fuel injection pump from rotating. The shaft of the fuel injection pump must not be rotated after the fuel injection pump has been removed from the engine.
Illustration 2 g01349818
Remove nut (15). Remove bolt (14).
Remove bolt (16) and bracket (13) from the cylinder block.
Remove bolts (10) and washers (11) in order to remove fuel injection pump (4). Note: The fuel injection pump should be supported by hand as the bolts are removed.
Remove the fuel injection pump from the front housing. Remove O-ring seal (12).


Parts end Mariner:

2940
 
2940 END PLAT ASS'Y
7050200, 7050716, 7060507, 7060528, 7070520, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629, 7150629, 7175629, 7200620
75387
 
75387 END CAP ASSEMBLY, COMMUTATOR
7070509, 7080508, 7080629
6357A 1
 
6357A 1 END CAP ASSEMBLY, UPPER
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
8849
 
8849 END CAP ASSEMBLY, COMMUTATOR
7050716, 7060312PC, 7060524, 7070520, 7075524, 7080629
12660
 
12660 END FRAME KIT
7045217, 7050717, 7060312PC, 7075312ND, 7075312SD, 7075524, 7075717, 7090524, 7100412NC, 7115520, 71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727
5826A 2
 
5826A 2 END CAP ASSEMBLY, UPPER
70404119D, 7045217, 7050200, 7050716
6635A 1
 
6635A 1 END CAP ASSEMBLY, LOWER
7045217, 7050200, 7050716
75383
 
75383 END CAP, COMMUTATOR
70404119D, 7045217, 7050200, 7050302ED, 7050412YD, 7050716, 7060412ET, 7075717
Back to top