856744 1 Mariner FITTING


856744 1 FITTING Mariner 7135473GD, 7135473HD, 7200473GD, 7200473HD FITTING
856744 1 FITTING Mariner
Rating:
48

Buy FITTING 856744 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Compatible models:

Mariner entire parts catalog list:

7135473GD 1998
7135473HD 1999
7200473GD 1998
7200473HD 1999

Information:

continues to run.Test Step 1. Inspect Electrical Connectors and Wiring
Shut down the engine.
Turn the Engine Control Switch (ECS) to the OFF/RESET position.
Turn the main disconnect switch to the OFF position.
Thoroughly inspect all of the connectors that are associated with the circuit.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check For Diagnostic Codes and Fault Indicators
Turn the main disconnect switch to the ON position.
Start the engine.
Check for diagnostic codes and fault indicators on the Status Control Module (SCM).Expected Result:There is a diagnostic code or a fault indicator that is displayed.Results:
OK - There is a diagnostic code or a fault indicator that is displayed. If the energize to Shutdown (ETS) fuel system is supported, go to Test Step 3.
OK - There is a diagnostic code or a fault indicator that is displayed. If the energize to Run (ETR) fuel system is supported, go to Test Step 4.
Not OK - There is not a diagnostic code or a fault indicator that is displayed. Proceed to Test Step 5.Test Step 3. Check the ETS Fuel System
Measure the voltage at the following locations while the engine is running and the fault indicator(s) illuminated:
Terminal 23 at the SCM
Terminal S at the SCM
Terminal R at the SCMExpected Result:The voltage is above 20 VDC for all three measurements.Results:
OK - The voltage is above 20 VDC for all three measurements.Repair: There may be an open in the wire from the fuel solenoid to terminal 23 at the SCM.Repair the connectors or wiring and/or replace the connectors or wiring. If the wire is OK, troubleshoot the fuel solenoid.Verify that the repair eliminates the problem.STOP
Not OK - The voltage is below 20 VDC at terminal 23. The voltage is above 20 VDC for the other measurements.Repair: There may be a problem with the Fuel Control Relay (FCR).Proceed to Testing and Adjusting, "Relay module - Test".STOP
Not OK - The voltage is not below 20 VDC at terminal R. The voltage is below 20 VDC for the other measurements.Repair: Replace the fuse F6.There may be a problem in the wire harness between the fuel solenoid and the SCM.Repair the connectors or wiring and/or replace the connectors or wiring. Verify that the repair eliminates the problem.STOP
Not OK - The voltage is below 20 VDC for all three measurements.Repair: There may be a problem in the wire harness between the +Battery and terminal R at the SCM.Repair the connectors or wiring and/or replace the connectors or wiring. Replace the battery, if necessary.Verify that the repair eliminates the problem.STOPTest Step 4. Check the ETR Fuel SystemCarefully remove the fuse F6.Expected Result:The engine shuts down.Results:
OK - The engine shuts down.Repair: Verify that the FCR is not stuck in the closed position.Check the resistance between terminal 23 and terminal S at the SCM.If the resistance is below 5 Ohms, proceed to Testing and Adjusting, "Relay module - Test".If the resistance is not below 5 Ohms, troubleshoot the circuit for the Gas Shutoff Valve (GSOV).Verify that the repair eliminates the problem.STOP
Not OK - The engine does not shut down.Repair: The GSOV is stuck in the run position.Shut down the engine and troubleshoot the GSOV.Verify that the repair eliminates the problem.STOPTest Step 5. Check the SetpointsCheck the setpoint programming.Expected Result:The setpoint programming is OK.Results:
OK - The setpoint programming is OK.Repair: There may be an intermittent problem.Inspect the electrical connectors and wiring.If necessary, repair the connectors or wiring and/or replace the connectors or wiring.Verify that the repair eliminates the problem.STOP
Not OK - The setpoint programming is not OK.Repair: A setpoint(s) is programmed to ignore fault conditions.Reprogram the setpoints.Proceed to Testing and Adjusting, "Setpoint Programming".Verify that the repair eliminates the problem.STOP


Parts fitting Mariner:

64705
 
64705 FITTING, FUEL PUMP (OUTLET)
7045217, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075312ND, 7075312SD, 7075524, 7075717, 7080508, 7080629, 7085507, 7090520, 7090524, 7115520, 7135417PD, 7135473GD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200473GD
68728
 
68728 FITTING
7002201DK, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135826, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413AD, 7175413PD, 7
19688
 
19688 FITTING
7050412YD, 7050717, 7060312PC, 7060412ET, 7075312ND, 7075312SD, 7090524, 7100412NC, 7115520, 71354120D, 7135417PD, 7135473GD, 7150453PD, 7175412PD, 7175629, 7200412PD, 7200620, 7250422PD
855424 7
 
855424 7 FITTING
7135473GD
855424
 
855424 FITTING
7135473GD, 7135473HD
855424 1
 
855424 1 FITTING
7135473GD, 7135473HD, 7200D73MD, 7225E73MD, 7A30302LB, 7A41412LB
853339 3
 
853339 3 FITTING
7200473GD, 7200473HD
62365 1
 
62365 1 FITTING
7200473GD, 7200473HD
Back to top