16610M Mariner FUEL CONNECTOR, ENGINE END


16610M FUEL CONNECTOR, ENGINE END Mariner 7025500, 7026226, 7030205 FUEL
16610M FUEL CONNECTOR, ENGINE END Mariner
Rating:
33

Buy FUEL CONNECTOR, ENGINE END 16610M Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$21.96
 

14-07-2021
0.26[0.00] Pounds
-: -
ACDelco Professional 16610M Molded Heater Hose
Comes with a protective sleeve to help duplicate GM OE designs for proper fit and function || Installs without buckling, bending out of shape, or straining at the connection for easy installation || Has all the quality features of a regular coolant hose for interchangeable use || Its diameter ranges from 1/4 in to 1 in to fit different types of vehicles || Less than 500 part numbers cover more than 1,200 applications to maximize coverage and reduce inventory
Number on catalog scheme: 19
 

Compatible models:

Mariner entire parts catalog list:

7025500 1980
7026226 1986,1988
7030205 1985,1986,1987,1988,1989,1990

Information:

Engine ECM
The engine is equipped with an Electronic Control Module (ECM). The ECM contains no moving parts. Follow the troubleshooting procedures in this manual to be sure that replacing the ECM will correct a fault. Verify that the suspect ECM is the cause of the fault.Note: Ensure that the ECM is receiving power and that the ECM is properly grounded before replacement of the ECM is attempted. Refer to the schematic diagram.A test ECM can be used to determine if the ECM on the engine is faulty. Install a test ECM in place of the suspect ECM. Install the flash file with the correct part number into the test ECM. Program the parameters for the test ECM. The parameters must match the parameters in the suspect ECM. Refer to the following test steps for details. If the test ECM resolves the fault, reconnect the suspect ECM. Verify that the fault returns. If the fault returns, replace the ECM.Note: If an ECM is used as a test ECM, select "Test ECM Mode" on the electronic service tool before the engine serial number is entered.Use the electronic service tool to read the parameters in the suspect ECM. Record the parameters in the suspect ECM. Install the flash file into the new ECM. After the ECM is installed on the engine, the parameters must be programmed into the new ECM.Note: When a new ECM is not available, an ECM can be used from an engine that is not in service. The ECM must have the same serial number suffix. Ensure that the replacement ECM and the part number for the flash file match the suspect ECM. Be sure to record the parameters from the replacement ECM. Use the "Copy Configuration ECM Replacement" function in the electronic service tool.
If the flash file and engine application are not matched, engine damage may result.
Perform the following procedure to replace the ECM.
Connect the electronic service tool to the diagnostic connector.
Use the "Copy Configuration ECM Replacement" function from the electronic service tool. If the "Copy Configuration" is successful, proceed to Step 4. If the "Copy Configuration" failed, proceed to Step .Note: Record any Logged Faults and Events for your records.
Record the following parameters:
Record all the parameters on the "Configuration" screen.
Record all the parameters on the "Throttle Configuration" screen.
Record all the parameters on the "Mode Configuration" screen.
Record the serial numbers of the electronic unit injectors. The injector serial numbers are shown on the "Injector Trim Calibration" screen.
Record the data from the "Current Totals" screen.Note: If the parameters cannot be read, the parameters must be obtained elsewhere. Some parameters are stamped on the engine information plate, but most parameters must be obtained from PTMI data.
Remove power from the ECM.
Remove the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Install the replacement ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
If the replacement ECM is used as a test ECM, select "Test ECM Mode" on the electronic service tool.
Download the flash file.
Connect the electronic service tool to the diagnostic connector.
Select "WinFlash" from the "Utilities" menu of the electronic service tool.
Select the downloaded flash file.
If necessary, use the electronic service tool to clear the rating interlock. To clear the rating interlock, enter the factory password when the electronic service tool is first connected. Activating the Test ECM mode will also clear the rating interlock.
Use the electronic service tool to program the parameters. Perform the following procedure.
If the "Copy Configuration" procedure was successful, use the "Copy Configuration, ECM Replacement" function to load the configuration file into the ECM.Note: During the following procedure, factory passwords may be required.
If the "Copy Configuration" procedure failed, configure the parameters individually. The parameters should match the parameters from step 3.
Perform the "High Pressure Fuel Pump Calibration".
Check for logged diagnostic codes. Factory passwords are required to clear logged events.


Parts fuel Mariner:

14187M
FUEL CONNECTOR
14187M FUEL CONNECTOR
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008237, 7008305, 7010209, 7015529, 7025500, 7026226, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040706, 7040716, 7055324, 7055524
18925M
 
18925M FUEL LINE ASS'Y (5/16"-8MM-I.D. HOSE)
7005201, 7005207, 7025500, 7026226, 7030205, 7040207PW, 7055524
16570M
FUEL LINE ASS'Y (1/4"-6MM-I.D. HOSE)
16570M FUEL LINE ASS'Y (1/4"-6MM-I.D. HOSE)
7004201, 7005201, 7005207, 7008208, 7008226, 7025500, 7026226, 7030205, 7030301, 7040206, 7040207PW, 7055524
95483M
 
95483M FUEL CONNECTOR, ENGINE
7008204, 7008226, 7020201, 7025200, 7025500, 7028527, 7030200, 7040202, 7040716
93099M
 
93099M FUEL CONNECOTR, ENGINE
7008208, 7008238, 7008248, 7020201, 7025200, 7025207NW, 7025500, 7028527, 7030200, 7040208, 7040328, 7040507, 7048227, 7048321, 7060507, 7060522
43113M
FUEL PUMP ASSEMLBY
43113M FUEL PUMP ASSEMLBY
7015327, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040706, 7040716, 7055324, 7055524
94799M
FUEL PUMP ASSEMBLY
94799M FUEL PUMP ASSEMBLY
7020201, 7025200, 7025207NW, 7025500, 7028527, 7030200, 7040208, 7040328
95216M
 
95216M FUEL LINE ASS'Y
7008204, 7008226, 7020201, 7025200, 7025500, 7028527, 7030200, 7030301, 7040202, 7040716, 7055524
Back to top