28862 Mariner GASKET


28862 GASKET Mariner 7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 70402 GASKET
28862 GASKET Mariner
Rating:
43

Buy GASKET 28862 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Mariner entire parts catalog list:

7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7005227 1977
7008204 1984,1985,1986
7008208 1978
7008226 1986
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7010209 1979,1983,1984,1985,1986
7015207 1977
7015307 1977
7015327 1987
7015529 1979
7020201 1981
7025200 1980
7025207NW 1988
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040207PW 1989,1990,1991,1992,1993
7040208 1978
7040328 1978,1980
7040507 1987
7040716 1986
7048207 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978
7070509 1979
7080508 1978,1979
7090529 1979
7115528 1978
7115529 1979
7140528 1978,1979
7140629 1979

Information:


Table 1
Event Code
Code and Description Conditions which Activate the Code System Response
E360(1) Low Engine Oil Pressure The engine oil pressure is less than the trip point and the delay time has expired. The code is logged.
Engine performance is not affected.
E360(2) Low Engine Oil Pressure The oil pressure continues to be below the specified pressure. The code is logged.
The engine is derated.
E360(3) Low Engine Oil Pressure The engine oil pressure has fallen below the trip point for the programmed delay time. The code is logged. The shutdown output is activated. The engine is shut down. Probable Causes
Low engine oil level
Incorrect viscosity
Contaminated engine oil
Faulty oil pressure sensors
Poor circulation of the engine oil
Worn componentsRecommended Repairs
Low Engine Oil Level
Check the oil level. Add oil, as needed.Incorrect Viscosity
Make sure that the engine is supplied with the correct engine oil. For the correct engine oil to use, refer to the Operation and Maintenance Manual.Contaminated Engine Oil
Engine oil that is contaminated with another liquid will cause low engine oil pressure. High engine oil level can be an indication of contamination. Obtain an analysis of the engine oil. Determine the reason for contamination of the engine oil and make the necessary repairs. Change the engine oil and the engine oil filter. For the correct engine oil to use, refer to the Operation and Maintenance Manual.Faulty Engine Oil Pressure Sensors
Use Cat ET to check the reading of the engine oil pressure while the engine is off. The reading should be close to zero pressure.If a reading is different from zero, replace the suspect engine oil pressure sensor.Poor Circulation of the Engine Oil
Several factors could cause poor circulation of the engine oil:
The engine oil filter is clogged. Replace the engine oil filter.
An engine oil line or a passage for engine oil is disconnected or broken.
The engine oil cooler is clogged. Thoroughly clean the engine oil cooler.
There is a problem with a piston cooling jet. Breakage, a restriction, or incorrect installation of a piston cooling jet will cause seizure of the piston.
The inlet screen of the suction tube for the engine oil pump can have a restriction. This restriction will cause cavitation and a loss of engine oil pressure. Check the inlet screen on the suction tube and remove any material that may be restricting engine oil flow.
The suction tube is drawing in air. Check the joints of the tube for cracks or for a damaged O-ring seal.
There is a problem with the engine oil pump. Check the gears of the engine oil pump for excessive wear. Engine oil pressure is reduced by gears that have too much wear.
The engine oil pumps pressure regulating valve or a bypass valve is stuck in the open position. Clean the valve. Replace parts, if necessary.Worn Components
Excessive clearance at the crankshaft or camshaft bearings will cause low engine oil pressure. Also, inspect the clearance between the rocker arm shafts and the rocker arms. Check the engine components for excessive clearance.Obtain an analysis of the engine oil. Check the analysis for the level of wear metals in the engine oil.


Parts gasket Mariner:

80972M
 
80972M GASKET, FLOAT CHAMBER
7004201, 7005201, 7005207, 7005227
96386M
 
96386M GASKET SET, POWERHEAD
7005201, 7005207
80271M
 
80271M GASKET
7005201, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7028207, 7028527, 7030200, 7030301, 7040207, 7040208, 7040208PW,
80449M
 
80449M GASKET, FLOAT BOWL...
7008238, 7008247
80912M
 
80912M GASKET, GEAR HOUSING
7015207, 7015307, 7015327
81574M
 
81574M GASKET, EXHAUST MANIFOLD
7020201, 7025200, 7025500, 7026226, 7028207, 7028527
96658M
 
96658M GASKET SET, POWERHEAD
7028527, 7030200, 7030205, 7030301
Back to top