41272M Mariner GASKET, PROTECTOR


41272M GASKET, PROTECTOR Mariner 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030301, 7030320 GASKET
41272M GASKET, PROTECTOR Mariner
Rating:
33

Buy GASKET, PROTECTOR 41272M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Mariner entire parts catalog list:

7020201 1981
7025200 1980
7025500 1980
7026226 1986,1988
7028527 1977
7030200 1980
7030301 1981
7030320 1980,1990,1992

Information:

Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris. Note: If equipped, be sure to flush the heater and any related supply and return lines.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques. Fill
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with Extended Life Coolant (ELC). Refer to the Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section) for more information on cooling system specifications. For additional information, refer to Special Publication, SEBU6385, "Caterpillar On-highway Diesel Truck Engine Fluid Recommendations". Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Run the engine at high idle for one minute in order to purge the air from the cavities of the engine block. Stop the engine.
Check the coolant level. Maintain the coolant level within 13 mm (0.5 inch) below the bottom of the pipe for filling. Maintain the coolant level within 13 mm (0.5 inch) to the proper level on the sight glass (if equipped).
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap and install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts gasket Mariner:

80590M
 
80590M GASKET, FLOAT BOWL
7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
81565M
 
81565M GASKET, OIL SEAL HOUSING
7020201, 7025200, 7025500, 7026226, 7028207, 7028527
81573M
 
81573M GASKET, EXHAUSST MANIFOLD
7020201, 7025200, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
80690M
 
80690M GASKET, FLYWHEEL COVER
7025200, 7025207NW, 7025207PW, 7025500, 7028207, 7028527
81600M
 
81600M GASKET, WATER PUMP
7028207, 7028527
84177M
816977
GASKET
816977 GASKET
7010207HB, 7010209, 7015201LD, 7015529, 7030320, 7040706, 7040716
95656M
 
95656M GASKET, WATER PUMP
7025500, 7026226, 7030205, 7030301, 7030320
Back to top