43337 4 Mariner GASKET, Drive Shaft Housing


43337 4 GASKET, Drive Shaft Housing Mariner 70152374D, 7020201HB, 7020201TB GASKET
43337 4 GASKET, Drive Shaft Housing Mariner
Rating:
93

Buy GASKET, Drive Shaft Housing 43337 4 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$54.99
 

26-05-2024

US: The ROP Shop
The ROP Shop | Fuel Primer Choke Solenoid Assy for Evinrude, Johnson, OMC & BRP 0433374, 433374
The ROP Shop The ROP Shop replacement Fuel Primer Choke Solenoid Assy for Evinrude, Johnson, OMC & BRP 0433374, 433374 || Specs - Refer to images 2 & 3 for more information || Includes - (1) Fuel Primer Choke Solenoid; comes as shown in the first image || Please be sure to check your part or model number to ensure this is the correct fuel primer choke solenoid for your unit. Also, please note this may replace multiple part numbers
Number on catalog scheme: 13
 

Compatible models:

Mariner entire parts catalog list:

70152374D 1994,1995,1996,1997,1998
7020201HB 1999,2000,2001,2002,2003,2004
7020201TB 2005,2006

Information:


Table 1
Diagnostic Codes
CDL Code Code Description Comments
168-2 Electrical System Voltage : Erratic, Intermittent, or Incorrect The engine is running. The battery voltage falls below 6 VDC and the voltage returns above 9 VDC for three voltage readings in the last seven seconds.
168-3 Electrical System Voltage : Voltage Above Normal The ECM detects voltage that is above the acceptable value.
168-4 Electrical System Voltage : Voltage Below Normal The ECM detects voltage that is below the acceptable value.
1834-2 Ignition Key Switch loss of signal The ECM detects an erratic signal from the keyswitch. The keyswitch is cycled at least three times in the last second. The engine ECM requires the keyswitch to be in the ON position in order to maintain communications with Cat® Electronic Technician (ET).
Illustration 1 g02060084
Schematic for the electrical power supply circuit
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat ET to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
Codes
Result: An active 168-2 or 1834-2 code is present.
Proceed to Test Step 2.
Result: An active 168-3 is present.
Proceed to Test Step 3.
Results: An active 168-4 is present.
Proceed to Test Step 4.
2. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the connectors.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Proceed to Test Step 3.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Charging Circuit
Charging Circuit
Result: The battery voltage is high.
Repair: There is a problem with the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".
If the problem is not resolved, proceed to Test Step 4.
4. Check the Battery
A. Turn the keyswitch to the ON position. Do not start the engine.
a. Check the brightness of the lights.
B. Turn the keyswitch to the ON position. Start the engine.
a. Check the brightness of the lights.
Battery
Result: The lights are dim when the engine is not running. The lights are brighter when the engine is running.
Repair: There is a problem with the battery. Proceed to Test Step 5.
Result: The lights are dim when the engine is not running. The lights are still dim when the engine is running.
Repair: There is a problem with the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".
If the problem is not resolved, proceed to Test Step 5.
5. Check the Battery Charge
A. Measure the no-load battery voltage at the battery posts.
B. Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 Volt and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure".
Battery Charge
Result: The batteries pass the load test. The measured voltage is between 11.0 VDC and 13.5 VDC for a 12 V system and between 22.0 VDC and 27.0 VDC for a 24 V system.
Repair: Check the wiring between the batteries and the ECM.
Check the connectors between the batteries and the ECM for moisture and/or corrosion.
Repair the wiring and/or the connectors.
Verify that the repair eliminates the problem.
Result: The battery voltage is low or the battery did not pass the load test.
Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts gasket Mariner:

41499A87
 
41499A87 GASKET SET
70152374D, 7020201HB, 7020201NC, 7020207
41499 1
 
41499 1 GASKET, SCHAUST COVER
7020201HB, 7020201TB, 7020207
86389
 
86389 GASKET, CYLINDER BLOCK COVER
7020201HB, 7020201TB, 7020207
41670
 
41670 GASKET, ADAPTOR, PLATE
7020201HB, 7020207
19206 1
 
19206 1 GASKET, CARBURETOR
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201TB
9633
 
9633 GASKET
7006201HB, 7006201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB
41417 2
 
41417 2 GASKET
70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB
9761 1
 
9761 1 GASKET/DIAPHRAGM KIT
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201TB
Back to top