72507 Mariner GASKET, CYLINDER BLOCK TO BAFFLE PLATE


72507 GASKET, CYLINDER BLOCK TO BAFFLE PLATE Mariner 7115528, 7115529, 7140528, 7140629 GASKET
72507 GASKET, CYLINDER BLOCK TO BAFFLE PLATE Mariner
Rating:
13

Buy GASKET, CYLINDER BLOCK TO BAFFLE PLATE 72507 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

Mariner entire parts catalog list:

Information:


Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
E265(3) User Defined Shutdown     The inputs from the ground level shutdown switch to the Electronic Control Module (ECM) have changed states.     The engine will shut down. The code is logged.    
267-3 Remote Shutdown Input voltage above normal     Both of the switch contacts of the ground level shutdown switch are in the open state.     If both of the switch contacts from the ground level shutdown switch change to the same state and the engine is running, the engine will continue to run. The code is logged.    
267-4 Remote Shutdown Input voltage below normal     Both of the switch contacts of the ground level shutdown switch are in the closed state.    The ground level shutdown switch provides the ability to shut down the engine. The engine's ECM remains active. Caterpillar Electronic Technician (ET) can be used to communicate with the ECM. The ground level shutdown switch must be returned to the RUN position and the engine rpm must be zero before the ECM will allow the engine to start.To shut down the engine, lift the red cover guard and toggle the ground level shutdown switch to the SHUTDOWN position. The ECM reads the position of the ground level shutdown switch. If the engine is running, the ECM disables the fuel injection. The status screen will display "INJECTION DISABLED" and "REMOTE SHUTDOWN".The ECM will not allow the engine to start if the status for the ground level shutdown switch is "REMOTE SHUTDOWN".
Illustration 1 g01397149
Schematic
Illustration 2 g01303342
P1 ECM connector (P1-54) user defined shutdown (NO) (P1-56) user defined shutdown (NC)Test Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connector J1/P1. Thoroughly inspect the connectors for the ground level shutdown switch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ground Level Shutdown Switch on Cat ET
Connect Cat ET to the service tool connector. Start Cat ET.
Turn the keyswitch to the ON position.
Observe the status of the ground level shutdown switch on Cat ET.
Operate the ground level shutdown switch. Observe the status of the ground level shutdown switch on Cat ET.Expected Result:The status of the ground level shutdown switch on Cat ET is REMOTE SHUTDOWN when the ground level shutdown switch is in the SHUTDOWN position.Results:
OK - The status of the ground level shutdown switch on Cat


Parts gasket Mariner:

2937
 
2937 GASKET, VALVE TO RESERVOIR
7050200, 7050716, 7060507, 7060528, 7070520, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
32433
 
32433 GASKET, LOWER - WATER PUMP BASE TO FACE PLATE
7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
32434
 
32434 GASKET, UPPER - FACE PLATE TO WATER PUMP BODY
7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
4808
 
4808 GASKET AND PACKING SET (1 PER CARBURETOR)
7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
48164
 
48164 GASKET, CARBURETOR FLANGE
7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
53862
 
53862 GASKET, CRANKCASE TO CYLINDER BLOCK
7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629, 7250422PD
55896
 
55896 GASKET, DISTRIBUTOR CAP
7115528, 7115529, 7140528, 7140629
72142
 
72142 GASKET, WATER JACKET COVER
7090520, 7115520, 7115528, 7115529, 7140528, 7140629
Back to top