98993M Mariner GASKET


98993M GASKET Mariner 7010209, 7015529 GASKET
98993M GASKET Mariner
Rating:
38

Buy GASKET 98993M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Compatible models:

7010209   7015529   Mariner

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979

Information:


Table 1
Diagnostic Codes Table
Code and Description Conditions which Generate this Code System Response
262-3 5 Volt Sensor DC Power Supply : Voltage Above Normal The analog sensor supply voltage is above normal for two seconds. The code is logged.
All sensors are set to default values.
262-4 5 Volt Sensor DC Power Supply : Voltage Below Normal The analog sensor supply voltage is below normal for two seconds.
263-3 Digital Sensor Power Supply (8V Or 12V) : Voltage Above Normal The digital sensor supply voltage is above normal for two seconds.
263-4 Digital Sensor Power Supply (8V Or 12V) : Voltage Below Normal The digital sensor supply voltage is below normal for two seconds. System OperationThe Electronic Control Module (ECM) supplies a regulated voltage of 5.0 0.2 VDC to the following sensors:
Aftercooler temperature sensor
Atmospheric pressure sensor
Coolant temperature sensor
Crankcase pressure sensor
Filtered engine oil pressure sensor
Filtered fuel pressure sensor
Turbocharger outlet pressure sensor
Left turbocharger inlet pressure sensor
Right turbocharger inlet pressure sensor
Unfiltered engine oil pressure sensor
Unfiltered fuel pressure sensorThe ECM supplies a regulated voltage of 8.0 0.4 VDC to the following sensors:
Left exhaust temperature sensor
Right exhaust temperature sensorThe supply voltage for the sensors is routed from the ECM to terminal A of each sensor connector. The sensor return for the sensors is routed from the ECM to terminal B of each sensor connector. The ECM provides short circuit protection for the internal power supply. A short circuit to the battery will not damage the internal power supply.Note: The sensors are not protected from overvoltage. A short from the supply line to the +Battery may damage the sensors. If the diagnostic code 262-3 or the diagnostic code 263-3 is logged, it is possible that all of the sensors have been damaged. Repair the sensor supply and check for any active sensor diagnostic codes in order to determine if a sensor has failed.
Illustration 1 g01340556
Typical schematic 5 V supply
Illustration 2 g01340557
Typical schematic 8 V supply
Illustration 3 g01327649
P1 ECM connector
(P1-2) "5 V analog sensor supply (LH)"
(P1-3) "Analog sensor return (LH)"
(P1-4) "8 V digital sensor supply (LH)"
(P1-5) "Digital sensor return (LH)"
(P1-18) "5 V analog sensor supply (RH)"
(P1-35) "Analog sensor return (RH)"
Illustration 4 g01327661
P2 ECM connector
(P2-56) "8 V digital sensor supply (RH)"
(P2-66) "Digital sensor return (RH)"
Illustration 5 g01327616
Terminal locations for the A-C1/E-C2 RH rigid harness connectors and the C-C1/E-C1 LH rigid harness connectors
(Terminal A) "Analog sensor return (RH)"
(Terminal B) "5 V analog sensor supply (RH)"
(Terminal C) "8 V digital sensor supply (RH)"
(Terminal D) "Digital sensor return (RH)"
Illustration 6 g01356892
Terminal locations for the AA-C67C-C20 connector for the fuel pressure sensors and for the oil pressure sensors
(Terminal B) "Analog return (LH)"
(Terminal C) "5 V analog sensor supply (LH)"
Illustration 7 g01356894
Terminal locations for the A-C48 connector for the coolant level sensors
(Terminal A) "8VDC digital supply"
(Terminal B) "Digital return"
Illustration 8 g01337991
Connector locations
(1) A-C1/E-C2 RH rigid harness connectors
(2) A-C2/J-C2 RH rigid harness connectors
(3) P-C1/A-C90 Connectors for the power distribution panel
(4) P-C2/A-C91 Connectors for the power distribution panel
(5) G-C6/F-C2/F-C1/A-C92 Connectors for a RH Control panel
(6) C-C22 Connection for the P2 ECM connector
(7) C-C15 Connection for the P1 ECM connector
(8) G-C6/F-C2/F-C1/C-C17 Connectors for a LH Control panel
(9) C-C18/TB-C1 Customer connectors
(10) C-C2/J-C1 LH rigid harness connectors
(11) C-C1/E-C1 LH rigid harness connectors
Illustration 9 g01234146
Location of ECM connectors


Parts gasket Mariner:

81320M
GASKET
81320M GASKET
7005201, 7005207, 7005227, 7008208, 7008218EW, 7008226, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7030301, 7040207, 7040208, 7040328, 704
80271M
 
80271M GASKET
7005201, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7028207, 7028527, 7030200, 7030301, 7040207, 7040208, 7040208PW,
18026
 
18026 GASKET, PICK-UP BODY
7004201, 7005201, 7005207, 7010209, 7015529, 7030205, 7030320, 7040207PW, 7040706, 7040716, 7055324, 7055524
80267M
 
80267M GASKET
7008208, 7008238, 7008248, 7008305, 7010209, 7015529, 7040207PW
84259M
 
84259M GASKET
7008208, 7008238, 7008248, 7008305, 7010209, 7015529
43115M
 
43115M GASKET
7008305, 7010209, 7015529
816977
GASKET
816977 GASKET
7010207HB, 7010209, 7015201LD, 7015529, 7030320, 7040706, 7040716
17540M
 
17540M GASKET
7010209, 7015529
Back to top