822442A84 GEAR HOUSING ASSEMBLY Mariner
7200473FD, 7200473GD, 7225412CD, 7225413DD
GEAR
Price: query
Rating:
Mariner entire parts catalog list:
- GEAR HSG(PROP SHAFT)STD. ROTATION(G438000 & UP) » 822442A84
- GEAR HSG(PROP SHAFT)COUNTER ROTATION(G438000 & UP) » 822442A84
- GEAR HSG(PROP SHAFT)COUNTER ROTATION(0G438000 & UP) » 822442A84
- GEAR HSG(DRIVE SHAFT)STD. ROTATION(G438000 & UP) » 822442A84
- GEAR HSG(DRIVE SHAFT)COUNTER ROTATION(G438000 & UP) » 822442A84
- GEAR HOUSING, PROPELLER SHAFT - STANDARD ROTATION » 822442A84
- GEAR HOUSING, PROPELLER SHAFT - COUNTER ROTATION » 822442A84
- GEAR HOUSING(DRIVESHAFT)(STANDARD ROTATION) » 822442A84
- GEAR HOUSING(DRIVESHAFT)(COUNTER ROTATION) » 822442A84
- G-HSG, PROP-STD-0G438000 AND UP-1623-822442C3 » 822442A84
- G-HSG, PROP-COUNTER-G438000 AND UP-1623-822442C3 » 822442A84
- G-HSG, DRIVE-STD-COUNTER-0G438000 AND UP-1623-822442C3 » 822442A84
- G-HSG, DRIVE-STD-COUNTER-0G438000 AND UP-1623-822442C3 » 822442A84
- G-HSG, PROP-STD-0G438000 AND UP-1623-822442C3 » 822442A84
- G-HSG, PROP-COUNTER-G438000 AND UP-1623-822442C3 » 822442A84
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
B 4C-8134 Seal Remover 1
1U-7600 Slide Hammer Puller Gp 1 Start By:
Remove the cylinder head assembly.
Clean the bottom face of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves to identify the correct position.Note: Do not stamp the heads of the valves. Stamping or punching the heads of the valves could cause the valves to fracture.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Illustration 1 g01333469
Typical example
Illustration 2 g01333471
Typical example
Use Tooling (A) to compress the appropriate valve spring (3). Remove valve keepers (1).Note: Do not compress the valve spring so that valve spring retainer (2) touches valve stem seal (4).
Remove Tooling (A).
Remove valve spring retainer (2). Remove valve spring (3).
Remove valve (5).
Use Tooling (B) to remove valve stem seal (4).
Repeat Steps 3 through 7 to remove the remaining inlet and exhaust valves.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
C 4C-6373 Seal Installer 1
4C-6366 Valve Guide Driver 1
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and all lubrication passages in the cylinder head are free from debris. Follow Steps 1.a through 1.e to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to Systems Operation, Testing and Adjusting, "Cylinder Head Inspect".
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves".
Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder Head Valves".
Illustration 3 g01333472
Typical example
Use Tooling (C) to install new valve stem seals (4) onto each of the valve guides.
Illustration 4 g01333471
Typical example
Illustration 5 g02891838
Lubricate the stem of valve (5) with clean engine oil. Install valve (5) in the appropriate position in the cylinder head. Check the depth of the valve below the face of the cylinder head. Refer to Systems Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information.
Install valve spring (3) to the cylinder head. Orientate valve spring (3) with the small pitch downward, as indicated. Position valve spring retainer (2) onto valve spring (3).
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Parts gear Mariner:
19301
822442A25
822442A26
826288A 1
824700A 1
822442A17
822442A14
822442A77