826287A 1 Mariner GEAR ASSEMBLY, Forward (INCLUDES PINION)


826287A 1 GEAR ASSEMBLY, Forward (INCLUDES PINION) Mariner 7200473FD, 7225412CD, 7225413DD GEAR
826287A 1 GEAR ASSEMBLY, Forward (INCLUDES PINION) Mariner
Rating:
78

Buy GEAR ASSEMBLY, Forward (INCLUDES PINION) 826287A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 57
 

Compatible models:

Mariner entire parts catalog list:

7200473FD 1997
7225412CD 1994,1995,1996,1997,1998
7225413DD 1995,1996,1997,1998

Information:


Illustration 1 g06060440
Rear view of engine
Table 1
Specification for 456-6313 Cylinder Block
Item Qty Part Specification Description
- During assembly, bottom of the plate, top of the block, and both the sides of the gasket plate must be free of all visible fuel, oil, water and gasket adhesives, assembly compounds, or any other contaminates.
A 24 8T-0099 Dowel Extension of the dowel from the top face of the cylinder block is 21.0 0.5 mm (0.83 0.02 inch).
1 2 5F-9657 O-Ring Seal Lubricate the bore lightly with the lubricant that is being sealed.
C 12 197-7008 Dowel Extension of the dowel from the top face of the cylinder block is 21.0 0.5 mm (0.83 0.02 inch).
2 14 101-1198 Camshaft Bearing All centerlines through oil holes in the camshaft bearings and the camshaft bearing junctions must be positioned as shown in Illustration 1 on each side of cylinder block.
Oil holes must be positioned from horizontal at an angle (D) of 20 5 degrees as shown in Illustration 1.
Bore in the cylinder block for camshaft bearing is 98.00 0.02 mm (3.858 0.001 inch).
E 7 223-1696 Crankshaft Bearing Cap Width of the crankshaft bearing cap is 340.030 0.015 mm (13.3870 0.0006 inch).
Width of cylinder block for main bearing cap is 339.985 0.015 mm (13.3852 0.0006 inch).
3 8 6V-3348 O-Ring Seal Lubricate the bore lightly with the lubricant that is being sealed.
F - - New dimension from centerline of crankshaft bearing bore to the top of the cylinder block is 586 mm (23.1 inch).
G - - New dimension from centerline of crankshaft bearing bore to bottom of cylinder block (pan rails) is 230 mm (9.1 inch).
H - - Bore in the cylinder block for the main bearings is 169.742 0.020 mm (6.6827 0.0008 inch).
Illustration 2 g03497817
Section B-B
Table 2
Item Qty Part Specification Description
J 1 7N-2047 Dowel Extension of the dowel from the rear face of the cylinder block is 6.0 0.5 mm (0.24 0.02 inch).
K 2 7N-2047 Dowel Extension of the dowel from the front face of the cylinder block is 6.0 0.5 mm (0.24 0.02 inch).
L 2 4N-0683 Dowel Extension of the dowel from the rear face of the cylinder block is 19.0 0.5 mm (0.75 0.02 inch).
M 2 7N-2044 Dowel Extension of the dowel from the front face of the cylinder block is 40.0 0.5 mm (1.57 0.02 inch).
Illustration 3 g06060441
Front view
Table 3
Item Qty Part Specification Description
4 3 4W-4813 Plug Torque to 100 15 N m (74 11 lb ft).
5 3 8T-2929 O-Ring Seal During assembly, apply Krytox GPL-205 to secure O-rings.
6 3 8T-2928 O-Ring Seal Lightly lubricate the bore with 5P-3975 Rubber Lubricant.
7 28 7X-7925 Bolt Use the following procedure to tighten the crankshaft bearing cap bolts:
1. Before assembly, lubricate the threads completely with clean engine oil.
2. Hand tighten the bolts in the tapped holes.
3. Tighten the bolts in the numerical sequence as shown in Illustration 3 to 190 14 N m (140 10 lb ft).
4. Again, tighten the bolts for an extra angle of 180 5 degrees.


Parts gear Mariner:

19301
 
19301 GEAR
7200413JD, 7225412CD, 7225412HD, 7225413DD, 7225413HD
822442A25
 
822442A25 GEAR HOUSING ASSEMBLY, Basic - Black
7200473FD, 7225412CD, 7225413DD
822442A26
 
822442A26 GEAR HOUSING ASSEMBLY, Basic - Gray
7200473FD, 7225412CD, 7225413DD
826288A 1
 
826288A 1 GEAR ASSEMBLY, Reverse
7200473FD, 7225412CD, 7225413DD
824700A 1
822442A17
822442A14
822442A77
 
822442A77 GEAR HOUSING ASSEMBLY
7200473FD, 7200473GD, 7225412CD, 7225413DD
Back to top