99727A 1 Mariner GEAR, Drive


99727A 1 GEAR, Drive Mariner 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200412PD, 7200620, 7220727 GEAR
99727A 1 GEAR, Drive Mariner
Rating:
73

Buy GEAR, Drive 99727A 1 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$179.19
 

18-05-2022
5.6[2.25] Pounds
-: -
MERCURY Gear KIT-Drive mfg Part Number 99727A1
SKU: 43-99727A1 || Sold Each || Please verify your own fitment
Number on catalog scheme: 4
 

Mariner entire parts catalog list:

7135417PD 1989
7135826 1986,1987,1988
7150453ND 1988
7150453PD 1989,1990
7150629 1979,1980,1982,1984,1985
7175412PD 1989
7175629 1979,1980,1985,1986,1988
7200412PD 1989,1990
7200620 1980,1982,1983,1984,1985,1986,1988
7220727 1987,1988

Information:


Illustration 1 g01234315
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Illustration 2 g01144470
Left side engine view (1) J1/P1 ECM connectors
Thoroughly inspect the J1/P1 ECM connectors and the J700/P700 engine shutdown switch connector. Also inspect each of the machine connectors that are in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01213917
Terminal locations at the P1 ECM connector (P1-5) Digital sensor return (P1-23) Engine shutdown switch (N/C) (P1-40) Engine shutdown switch (N/O)
Illustration 4 g01159881
Harness connector for the engine shutdown switch (Terminal A) Engine shutdown switch (N/O) (Terminal B) Digital return (Terminal C) Engine shutdown switch (N/C)
Perform a 45 N (10 lb) pull test on each of the wires for the engine shutdown switch.
Check the torque of the allen head screw on the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points from the switch back to the ECM.Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Shutdown Switch on Cat ET
Connect Cat ET to the service tool connector.
Restore electrical power to the ECM.
Monitor the status screen on Cat ET while you operate the shutdown switch. Observe the status for the shutdown switch.Note: Wait at least 30 seconds for the status of the switch to change.Expected Result:The status of the shutdown switch reads "ON" with the shutdown switch in the STOP position. The status of the shutdown switch reads "OFF" when the shutdown switch is in the RUN position.Results:
OK - The status of the shutdown switch reads "ON" with the shutdown switch in the STOP position. The status of the shutdown switch reads "OFF" when the shutdown switch is in the RUN position. The shutdown switch is operating normally.Repair: The circuit for the shutdown switch appears to be operating correctly. There may be an intermittent problem in the harness or in a connector. If an intermittent problem is suspected, refer to Troubleshooting, "Inspecting Electrical Connectors".STOP
Not OK - The status of the switch does not read "ON" with the shutdown switch in the STOP position. The status of the shutdown switch does not read "OFF" when the shutdown switch is in the RUN position. There is a problem with the circuit for the shutdown switch. There may be a problem with the ECM. Proceed to Test Step 3.Test Step 3. Short the Terminals at the Harness Connector for the Shutdown Switch
Remove electrical power from the ECM.
Fabricate a


Parts gear Mariner:

9148A18
 
9148A18 GEAR HOUSING ASSEMBLY, Standard Rotation 2:1 Gear Ratio
7002201DK, 71354120D, 7135412AD, 7135417PD, 7135826, 7150629, 7175413AD, 7175629
9148A19
 
9148A19 GEAR HOUSING ASSEMBLY, Standard Rotation 2:1 Gear Ratio
7002201DK, 71354120D, 7135412AD, 7135417PD, 7135826, 7150629, 7175629
9148A22
9148A23
 
9148A23 GEAR HOUSING ASSEMBLY, COMPLETE
7135417PD, 7135826, 7150629
9148A 8
 
9148A 8 GEAR HOUSING
71354120D, 7175412PD, 7175413AD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727
9572A 1
 
9572A 1 GEAR HOUSING (BLACK)
7150453ND, 7150453PD
9572A 2
 
9572A 2 GEAR HOUSING (GRAY)
7150453ND, 7150453PD
9148A38
Back to top