9315M Mariner GEARHOUSING ASS'Y (LONG SHAFT)


9315M GEARHOUSING ASS'Y (LONG SHAFT) Mariner 7008204, 7008208, 7008226 GEARHOUSING
9315M GEARHOUSING ASS'Y (LONG SHAFT) Mariner
Rating:
43

Buy GEARHOUSING ASS'Y (LONG SHAFT) 9315M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 0-1
 

Compatible models:

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008226 1986

Information:


Illustration 1 g01252640
Schematic for the pressure sensor supply
Illustration 2 g01252645
Sensor locations for the pressure sensor supply (typical left side engine view) (1) Intake manifold pressure sensor (2) Barometric pressure sensor (3) Engine oil pressure sensor (4) J2/P2 ECM connectors
Illustration 3 g01252746
Terminal locations at the P2 ECM connector for the engine pressure sensors (P2-15) Intake manifold pressure sensor (P2-17) Sensor return (P2-28) Engine oil pressure sensor (P2-57) Barometric pressure sensor (P2-72) Sensor supply
Illustration 4 g01159881
Terminal locations at the sensor connector for the engine pressure sensors (Terminal A) Sensor supply (Terminal B) Sensor return (Terminal C) Sensor signalTest Step 1. Determine if the Code is Logged or Active
Connect Cat ET to the service tool connector.
Restore electrical power to the engine ECM.
Monitor the active diagnostic code and the logged diagnostic codes on Cat ET.Note: Wait at least 30 seconds in order for diagnostic codes to become active.Identify the diagnostic code.Results:
Logged code - Repair: Do not troubleshoot a logged code unless the code relates to an operator complaint. If the code is logged and the code does not relate to an operator complaint, clear the code. If the code is logged and the code relates to an operator complaint, proceed to Test Step 2.
Active code - Proceed to Test Step 3.Test Step 2. Check the Integrity of the Connections at the Connectors
Turn the keyswitch to the ON position. Do not start the engine.
Install a 7X-1708 Multimeter Probe (RED) and a 7X-1709 Multimeter Probe (BLACK) onto the test leads of a multimeter.Note: Ensure that the multimeter probes are in good repair. Bent probes may contact other terminals inside the connector.
Check for an intermittent problem at the connector for the suspect sensor:Note: Do not disconnect any harness connectors in order to perform this procedure.
Carefully install the spoons (multimeter probes) into the terminal locations for the sensor supply and the sensor return at the P2 ECM connector.
While you observe the voltage reading on the multimeter, wiggle the wires and pull on the wires at the connector for the suspect sensor.The voltage reading will not vary more than 0.5 volts for a solid electrical connection.
Remove the spoons (multimeter probes) from the connector.
Check for an intermittent problem at the ECM connector:Note: Do not disconnect any harness connectors in order to perform this procedure.
Carefully install the spoons (multimeter probes) into the terminal locations for the sensor supply and the sensor return at the connector for the suspect sensor.
While you observe the voltage reading on the multimeter, wiggle the wires and pull on the wires for the pressure sensor supply and the sensor return at the ECM connector.The voltage reading will not vary more than 0.5 volts for a solid electrical connection.
Remove the spoons (multimeter probes) from the connector.
Turn the keyswitch to the OFF position.Expected Result:The voltage reading did not vary more than 0.5 volts during either test.Results:
OK - The voltage reading did not vary more than 0.5 volts.Repair: The connections are OK at the connectors. There does not appear to be an intermittent problem in the circuit at this time. Return the engine to service.STOP
Not OK - The voltage reading varied more than 0.5 volts during the test.Repair: Disconnect the suspect connector and inspect the connector and the terminals for moisture, damage, and corrosion. Repair the connectors and/or the terminals. Return the engine to service.STOPTest Step 3. Check the Supply Voltage at the Sensor ConnectorMeasure the voltage between terminal 1 (sensor supply) and terminal 2 (sensor return) at the harness connector for the sensor that relates to the code.Expected Result:The voltage is between 4.5 VDC and 5.5 VDC.Results:
OK - The voltage is between 4.5 VDC and 5.5 VDC. The supply voltage is at the sensor connector. Record the voltage measurement. If you are troubleshooting a -3 diagnostic code, proceed to Te


Parts gearhousing Mariner:

6888M
 
6888M GEARHOUSING ASS'Y (SHORT SHAFT)...
7008208, 7008238, 7008247, 7008248, 7008305
6889M
 
6889M GEARHOUSING ASS'Y (LONG SHAFT)...
7008208, 7008238, 7008247, 7008248, 7008305
9314M
 
9314M GEARHOUSING ASS'Y (SHORT SHAFT)
7008204, 7008208, 7008226
Back to top